Clavister NetWall W20A Скачать руководство пользователя страница 7

Страница: 7 / 89

Chapter 1: W20B Product Overview

• W20A and W20B Differences, page 7

• Unpacking the W20B, page 9

• Interfaces and Ports, page 11

• Hardware Sensor Monitoring, page 13

1.1. W20A and W20B Differences

There are two W20B models:

•

The older W20A.

•

The newer W20B.

This guide is applicable only for the newer W20B model.

Important: Some earlier cOS Core versions are not supported

The supported cOS Core versions are as follows:

•

The

W20A

can run any cOS Core version from 10.22.01 onwards.

•

The

W20B

can run any cOS Core version from 12.00.03 onwards.

Earlier versions than those stated above are not supported and a downgrade should not
be attempted.

W20B Differences

The principal differences in the W20B when compared with the W20A are as follows:

•

The W20B status LED is located at a different position.

•

The W20B power switch in not a rocker switch but a switch with a static position of either On

Содержание NetWall W20A


























































































Результаты поиска

Содержание NetWall W20A

Отзывы:

Похожие инструкции для NetWall W20A

Бренды по названию

Популярные бренды

Clavister NetWall W20A, Руководство по началу работы

Результаты поиска

Содержание NetWall W20A

Отзывы:

Похожие инструкции для NetWall W20A

Бренды по названию

Популярные бренды