Clavister NetWall W20A Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 89

background image

1.

The progress of the reset can be followed using a local console connection. If that is
required, open a console display window connected to the W20B local console port.

2.

Power off the W20B.

3.

Push in the recessed reset button on the W20B with a suitable pointed tip tool and keep
it pushed in. A suitable paper-clip could be used to do this.

4.

Power up the W20B while still holding the reset button in.

5.

Continue holding the button in for at least 30 seconds longer after the power is applied.

6.

If a console was connected in step 1, the console output will indicate that the hardware
has been reset to its factory defaults.

7.

Release the button and the W20B can now be configured as though it had been newly
delivered and had not been previously configured.

Important: The local console password will be reset to none

If a local console password was set this will also be reset to the factory default of no
password. If required, the local console password should be set later by choosing the
boot menu option

Enable Console Password

.

Chapter 5: Resetting to Factory Defaults

73

«
...
71
72
73
74
75
...
»

Содержание NetWall W20A


























































































Отзывы:

Нет отзывов

Похожие инструкции для NetWall W20A

Бренд: D-Link Страницы: 13

Бренд: Lab.gruppen Страницы: 35

Patton SmartNode 2300 Series

Бренд: Patton electronics Страницы: 2

Бренд: Paradyne Страницы: 12

Бренд: LogLogic Страницы: 30

Бренд: Mercusys Страницы: 35

IAR KickStart Kit TWR-K60N512-IAR

Бренд: IAR SYSTEMS Страницы: 8

Бренд: Aaeon Страницы: 61

Бренд: Gigabyte Страницы: 18

Бренд: Hauppauge Страницы: 55

Бренд: Supermicro Страницы: 15

Бренд: Crown Страницы: 7

Бренд: Digital Audio Corporation Страницы: 164

-K6-2/450 - MHz Processor

Бренд: AMD Страницы: 98

Бренд: NetComm Страницы: 75

Бренд: Proscend Страницы: 93

RuggedSwitch RS500

Бренд: RuggedCom Страницы: 16

Macho Rev. A (BW)

Бренд: Thermalright Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды