Clavister NetWall W20A Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 89

background image

Wizard step 3: Select transparent mode interfaces

This step allows any transparent mode interfaces to be set up. If no transparent mode interfaces
are required, leave this dialog in the default Normal Mode and go to the next step. Transparent
mode interfaces can be configured at any time later, outside of the wizard.

Note: This step is only available with version 11.04 or later

The step to optionally set up transparent mode interfaces in the startup wizard is only
available with cOS Core version 11.04 or later. Also, the available interface list shown
above will vary according to the platform on which cOS Core is running.

Chapter 4: cOS Core Configuration

36

«
...
34
35
36
37
38
...
»

Содержание NetWall W20A


























































































Отзывы:

Нет отзывов

Похожие инструкции для NetWall W20A

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 2

DES-3526 - Switch - Stackable

Бренд: D-Link Страницы: 258

Бренд: Aastra Страницы: 2

Бренд: Quatech Страницы: 27

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 16

Бренд: Patton electronics Страницы: 51

iW-RainboW-G30D

Бренд: iWave Страницы: 89

Бренд: Vivotek Страницы: 170

Бренд: Dialogic Страницы: 2

RCO-3000 Series

Бренд: C&T Solution Страницы: 96

Бренд: TRENDnet Страницы: 62

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Бренд: Baicells Страницы: 10

Бренд: Comway Страницы: 20

Kontron CP3005 Series

Бренд: S&T Страницы: 115

Бренд: Firetide Страницы: 32

Braswell Series

Бренд: Intel Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды