Clarke 7630073 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 48

background image

28

BEND NO. 2

Slide the stock to the #2 chalk mark (as in B), and bend it to 90°. Re-check the
angle.

BEND NO. 3

Reverse the stock end-for-end. Slide it to the #3 chalk mark (as in C), and bend
it to 45°. Re-check the angle.

BEND NO. 4

Slide the stock to the #4 chalk mark (as in D), and bend it to 90°. Re-check the
angle and that the top and bottom of the E are parallel.

To remove the part from the bender, remove the pin that holds the sharp-
angle-bend attachment.

FINISHING

Tack-weld the 3-1/2 in insert piece in piece between the legs of the “A”,
parallel to the top edge. Grind and sand all sharp corners.

LETTER F

STOCK REQUIRED

• 3/16” stock; 2” max. width

• 1x 10-3/8in blank

• 1 x 2-1/2 in blank

SETUP

Make a letter “L” as shown on page 33.

FINISHING

Position the 2-1/2” piece as shown and tack weld it.

Grind and sand all sharp corners.

«
...
26
27
28
29
30
...
»

Содержание 7630073

















































Отзывы:

Нет отзывов

Похожие инструкции для 7630073

Бренд: York Fitness Страницы: 34

Бренд: BARKO LOADERS Страницы: 85

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

Бренд: Hardt Страницы: 2

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

HQ Power VDL25BM

Бренд: Velleman Страницы: 3

Бренд: iGuzzini Страницы: 36

AQUIS ULTRAFLOW

Бренд: Waterous Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды