manualshive.com logo in svg

CITROEN Berlingo 2003, Руководство пользователя

Поделиться
Скачать
CITROEN Berlingo 2003 Скачать руководство пользователя страница 446

442

ELECTRICAL

SYSTEM

CHARGING CIRCUIT - ALTERNATOR WITH MONO-FUNCTION REGULATOR

ALL TYPES

Checking the alternator output

Connect as shown in the diagram opposite, using an ammeter 

(A)

, a voltmeter 

(V)

,

and a rheostat

(R) 

or a Volt/Ammeter/Rheostat combination.

Referring to the vehicle’s equipment specification 

(see table opposite),

adjust the

engine speed and rheostat charge to obtain 

U=13.5V

.

Reminder :

The excitation energising current will flow through the warning lamp;

check that the warning lamp comes on when the ignition is switched on. It should
go out when the engine has started (accelerate slightly). 

Checking the voltage regulator

Set the rheostat to zero and disconnect all the electrical consumers.
Display 

3000 alternator rpm

. If 

U

alternator is > 14.7 V, the regulator is faulty.

Note:

These tests should be performed with the engine hot and the battery fully

charged.

Method of reading the alternator speed

Fit a reflecting shim on the pulley of the alternator.
Adjust a stroboscope to the frequency equivalent to the control speed. 

(e.g.  2000 rpm = 2000/60 = 83 Hz)

Adjust the engine speed so that the shim appears fixed.

D1AP025C

A

: Ammeter

B

: Battery

G

: Generator

L

: Warning lamp

K1

and 

K2

: Switch

R

: Electric charge

S

: Shunt 200mV/200A

V

: Voltmeter

1

: Alternator.

Содержание Berlingo 2003



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды