manualshive.com logo in svg

CITROEN Berlingo 2003, Руководство пользователя

Поделиться
Скачать
CITROEN Berlingo 2003 Скачать руководство пользователя страница 152

148

ENGINE

CHECKING AND SETTING THE VALVE TIMING

Engines : 8HX - 8HW

B1EP18GC

Setting the timing.

Remove the upper timing cover

(1)

.

Rotate the engine by means of the crankshaft screw 

(2)

.

NOTE :

The pegging hole is located under the crankshaft bearing cap cover.

Peg the engine flywheel, using tool

[3]

.

Remove the lower timing cover 

(3)

.

Uncouple the exhaust line from the manifold.

IMPERATIVE : Uncouple the exhaust line in order to avoid damaging the front flexible pipe. Twisting,
pulling and bending the front flexible pipe reduces its life.

Remove: 
- The engine speed sensor

(6

).

- The belt retaining stop 

(5)

.

- The screw

(2)

.

- The crankshaft pinion

(4)

(with its magnetic track 

«a»

).

IMPERATIVE : The magnetic track should show no signs of damage and should not be approached
by any other source of magnetism. Should this not be adhered to, it is essential to replace the
crankshaft pinion.

Refit the screw 

(2)

.

B1BP2LXC

C3

Содержание Berlingo 2003



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды