manualshive.com logo in svg

CITROEN Berlingo 2003, Руководство пользователя

Поделиться
Скачать
CITROEN Berlingo 2003 Скачать руководство пользователя страница 174

170

ENGINE

CHECKING AND SETTING THE VALVE TIMING

Engine : RFN         

# 

2003

Fitting tension of the timing belt.

Remove the tool

[3]

.

(D) :

Maximum position.

(E) : 

Nominal tension position.

Using the hexagonal key

(C)

, turn the hub of the roller (anti-clockwise), to bring the index 

(10) 

to position 

(D)

so as

to tension the belt to the maximum.
Turn the eccentric hub 

(8) 

of the roller 

(9)

(clockwise), until the cursor 

(10)

just comes into contact with the peg 

[4]

.

IMPERATIVE : Never turn the eccentric hub (8) by a complete rotation if the tool [4] is in position.
NOTE : 

This operation enables you to place the index

(10)

in the nominal position

(E)

.

Tighten the screw 

(7)

to 

2 ± 0,2 m.daN 

holding the roller with the aid of the hexagonal key

(C)

.

Remove pegs 

[1], [2]

and

[4]

.

Checks.

Turn the crankshaft by two rotations (direction of engine rotation).

IMPERATIVE : Never rotate the crankshaft backwards.

Make sure that the timing is correctly set by refitting the pegs

[1]

and

[2]

.

Remove pegs 

[1]

and 

[2].

Rotate the crankshaft

ten times 

(direction of engine rotation).

Check the position of the index

(10)

.

If the tensioner index is not at its adjusting position 

(E)

, recommence the operation to tension the timing belt.

B1EK1T9D

B1EK1TAD

XSARA - XSARA PICASSO

Содержание Berlingo 2003



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды