CITROEN Berlingo 2003 Скачать руководство пользователя страница 122

Страница: 122 / 482

118

ENGINE

AUXILIARY EQUIPMENT DRIVE BELT

Engines : 8HX - 8HW

Markings on the dynamic tensioner roller.

"a"

Position of «maximum wear» of the auxiliary drive belt.

"b"

Normal position.

Refitting

NOTE :

Check that the tensioner roller moves freely (no tight spot). If this is not the

case, replace the tensioner roller.

Respect the direction of fitting of the drive belt.

Complete the setting of the belt, of both sides, by means of the tensioner roller.
Make sure that the drive belt is correctly positioned in the

«V»

grooves of the various

pulleys.

Move the tool

[2]

on the tensioner roller to remove the peg

[3]

B1EP18UD

Содержание Berlingo 2003



































































































































































































































































































































































































































































































Результаты поиска

Содержание Berlingo 2003

Отзывы:

Бренды по названию

Популярные бренды

CITROEN Berlingo 2003, Руководство пользователя

Результаты поиска

Содержание Berlingo 2003

Отзывы:

Бренды по названию

Популярные бренды