CITROEN Berlingo 2003 Скачать руководство пользователя страница 381

Страница: 381 / 482

377

BRAKES

HANDBRAKE (Adjustment)

Prior to adjustment.

- Release the handbrake.
- Drums rotating freely.

- No tight spot (If there is one, check if the primary or secondary cables are

correctly routed).

- Check that all the parts slide and move correctly.
- Bleed the main circuit.

Adjustment.

- Set the brake to the

4th

notch.

- Tighten the nut

(3)

until the rear brakes are applied.

- Check that:
- there is a total travel of between

4 and 7 notches

- the two secondary cables

(1)

on the balance lever

(2)

move together.

- the wheels rotate freely when the brake is released.
- Check that the brake warning lamp comes on from the

4th

notch.

NOTE :

The handbrake operates on the rear wheels.

B3FP106JC

SAXO - All Types

Содержание Berlingo 2003



































































































































































































































































































































































































































































































Результаты поиска

Содержание Berlingo 2003

Отзывы:

Бренды по названию

Популярные бренды

CITROEN Berlingo 2003, Руководство пользователя

Результаты поиска

Содержание Berlingo 2003

Отзывы:

Бренды по названию

Популярные бренды