CITROEN Berlingo 2003 Скачать руководство пользователя страница 246

Страница: 246 / 482

242

INJECTION

CHECKS : EXHAUST GASES RECYCLING CIRCUIT

Engines : 8HX - 8HW

Engines : 8HV - 8HY

TOOLS

[1] Manual pressure-vacuum pump

: FACOM DA 16.

IMPERATIVE : Respect the safety and cleanliness specific to high pressure diesel
injection (HDi) engines.

EGR valve

Connect tool

[1]

on the capsule take-off

(2).

Apply a vacuum of approx.

0,6 bar

several times to activate the rod

«a»

In abruptly suppressing the vacuum, the valve should click and lock itself back on its seating.

Regulation electrovalve (EGR). (Engine: 8HX-8HW).

Check to be performed between the electrovalve

(1)

and the EGR valve

(2)

Link the tool

[1]

in series, between the electrovalve

(1)

and the capsule

(2)

Compare the values noted with those in the table below.

Regulation electrovalve (EGR). (Engine: 8HV-8HY).

Check to be performed between the electrovalve

(2)

and the EGR valve

(1)

Link the tool

[1]

in series, between the electrovalve

(2)

and the capsule

(1)

Compare the values noted with those in the table below.

Engine speed (rpm)

Vacuum value

780

0.5

2500

B1HP15GD

B1HP1K6D

Содержание Berlingo 2003



































































































































































































































































































































































































































































































Результаты поиска

Содержание Berlingo 2003

Отзывы:

Бренды по названию

Популярные бренды

CITROEN Berlingo 2003, Руководство пользователя

Результаты поиска

Содержание Berlingo 2003

Отзывы:

Бренды по названию

Популярные бренды