manualshive.com logo in svg

Cisco ME 3600X, Справочник по командам

Коммутатор Cisco ME 3600X - это высокопроизводительное устройство для построения сетей. Установочный руководство и другие руководства пользователя доступны для загрузки бесплатно на manualshive.com. Получите все необходимые инструкции для установки и настройки оборудования для безупречной работы вашей сети.

Поделиться
Скачать
background image

 

2-120

Cisco ME 3800X and ME 3600X Switch Command Reference

OL-28238-01

Chapter 2      Cisco ME 3800X and ME 3600X Switch Cisco IOS Commands

ip sla reaction-configuration

ip sla reaction-configuration

To configure proactive threshold monitoring parameters for an IP Service Level Agreements (SLAs) 
operation, use the 

ip sla reaction-configuration

 command in global configuration mode. To disable all 

the threshold monitoring configuration for a specified IP SLAs operation, use the 

no

 form of this 

command.

ip sla reaction-configuration 

operation-number

 

{

react 

{

unavailableDS | unavailableSD 

}{

loss-ratioDS | loss-ratioSD

}[

threshold-type 

{

average

 [

number-of-measurements

] |

 

consecutive 

[

occurrences

] 

| immediate

 |

 never 

}] [

threshold-value 

upper-threshold

 

lower-threshold

]]

no ip sla reaction-configuration

 

operation-number

 [

react

 

monitored-element

]

Syntax Description

operation-number

Number of the IP SLAs operation for which reactions are to be configured.

react

 

Specifies the element to be monitored for threshold violations.

Note

The elements supported for monitoring will vary depending on the type of 
IP SLAs operation you are running. See the Usage Guidelines for 
information.

unavailableDS

Specifies that a reaction should occur if the percentage of destination-to-source 
Frame Loss Ratio (FLR) violates the upper threshold or lower threshold.

unavailableSD

Specifies that a reaction should occur if the percentage of source-to-destination 
FLR violates the upper threshold or lower threshold.

loss-ratioDS

Specifies that a reaction should occur if the one-way destination-to-source 
loss-ratio violates the upper threshold or lower threshold.

loss-ratioSD

Specifies that a reaction should occur if the one way source-to-destination 
loss-ratio violates the upper threshold or lower threshold.

threshold-type

 

average

 

[

number-of-measu

rements

]

(Optional) When the average of a specified number of measurements for the 
monitored element exceeds the upper threshold or when the average of a specified 
number of measurements for the monitored element drops below the lower 
threshold, perform the action defined by the action-type keyword. For example, if 
the upper threshold for

 reactrttthreshold-typeaverage3

 is configured as 5000 ms 

and the last three results of the operation are 6000, 6000, and 5000 ms, the average 
would be 6000 + 6000 + 5000 = 17000/3 = 5667, thus violating the 5000 ms upper 
threshold.

The default number of 5 averaged measurements can be changed using the 
number-of-measurements argument. The valid range is from 1 to 16.

threshold-type 
consecutive

 

[

occurrences

]

(Optional) When a threshold violation for the monitored element is met 
consecutively for a specified number of times, perform the action defined by the 
action-type keyword.

The default number of 5 consecutive occurrences can be changed using the 
occurrences argument. The valid range is from 1 to 16.

The occurrences value will appear in the output of the 

show ip sla 

reaction-configuration

 command as the "Threshold Count" value.

threshold-type 
immediate

(Optional) When a threshold violation for the monitored element is met, 
immediately perform the action defined by the action-type keyword.

Содержание ME 3600X





















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ME 3600X

D-Link DGS-3224TGR - Switch User Manual preview
DGS-3224TGR - Switch
Бренд: D-Link Страницы: 160
D-Link DGS-3024 User Manual preview
DGS-3024
Бренд: D-Link Страницы: 145
D-Link DGS-1510 Series Getting Started Manual preview
DGS-1510 Series
Бренд: D-Link Страницы: 64
D-Link DES-3528 - xStack Switch - Stackable Reference Manual preview
DES-3528 - xStack Switch - Stackable
Бренд: D-Link Страницы: 367
3Com Switch 4500 Family Datasheet preview
Switch 4500 Family
Бренд: 3Com Страницы: 16
3Com PathBuilder S200 Series User Manual preview
PathBuilder S200 Series
Бренд: 3Com Страницы: 32
Eaton AGswitch Instructions Manual preview
AGswitch
Бренд: Eaton Страницы: 36
Cabletron Systems 6H122-08 User Manual preview
6H122-08
Бренд: Cabletron Systems Страницы: 170
Linkskey LKV-T02 Quick Installation Manual preview
LKV-T02
Бренд: Linkskey Страницы: 2
Eaton S-T0 Instruction Leaflet preview
S-T0
Бренд: Eaton Страницы: 3
TRENDnet TI-IG30 Quick Installation Manual preview
TI-IG30
Бренд: TRENDnet Страницы: 10
G&D ControlCenter-Compact Manual preview
ControlCenter-Compact
Бренд: G&D Страницы: 68
PABX TC-2000 A Instruction Manual preview
TC-2000 A
Бренд: PABX Страницы: 16
CYP EL-41X Operation Manual preview
EL-41X
Бренд: CYP Страницы: 13
OEZ BD250NE300 Instructions For Use Manual preview
BD250NE300
Бренд: OEZ Страницы: 25
Dell PowerConnect B-8000 Hardware Reference Manual preview
PowerConnect B-8000
Бренд: Dell Страницы: 58
Pioneer VSW-1 Operating Instructions Manual preview
VSW-1
Бренд: Pioneer Страницы: 44
Rane LRS4 Datasheet preview
LRS4
Бренд: Rane Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды