manualshive.com logo in svg

Cisco 3845 - Security Bundle Router, Руководство пользователя программного обеспечения

Маршрутизатор Cisco 3845 - Security Bundle Router является надежным и безопасным решением для вашей сети. Скачайте бесплатно руководство по эксплуатации и программное обеспечение на {веб-сайт}, чтобы использовать его на максимуме. Узнайте все возможности и настройки вашего устройства.

Поделиться
Скачать
background image

 

29-47

Cisco ME 3800X and 3600X Switch Software Configuration Guide

OL-23400-01

Chapter 29      Configuring IP Unicast Routing

Configuring BGP

Switch(config-router)# 

neighbor 129.213.1.2 remote-as 100

Switch(config-router)# 

neighbor 175.220.1.2 remote-as 200

Router C:

Switch(config)# 

router bgp 200

Switch(config-router)# 

neighbor 175.220.212.1 remote-as 200

Switch(config-router)# 

neighbor 192.208.10.1 remote-as 300

Router D:

Switch(config)# 

router bgp 300

Switch(config-router)# 

neighbor 192.208.10.2 remote-as 200

To verify that BGP peers are running, use the show ip bgp neighbors privileged EXEC command. This 
is the output of this command on Router A:

Switch#

 show ip bgp neighbors

BGP neighbor is 129.213.1.1, remote AS 200, external link

 BGP version 4, remote router ID 175.220.212.1

 BGP state = established, table version = 3, up for 0:10:59

 Last read 0:00:29, hold time is 180, keepalive interval is 60 seconds

 Minimum time between advertisement runs is 30 seconds

 Received 2828 messages, 0 notifications, 0 in queue

 Sent 2826 messages, 0 notifications, 0 in queue

 Connections established 11; dropped 10

Anything other than state = established means that the peers are not running. The remote router ID is 
the highest IP address on that router (or the highest loopback interface). Each time the table is updated 
with new information, the table version number increments. A table version number that continually 
increments means that a route is flapping, causing continual routing updates.

For exterior protocols, a reference to an IP network from the network router configuration command 
controls only which networks are advertised. This is in contrast to Interior Gateway Protocols (IGPs), 
such as EIGRP, which also use the network command to specify where to send updates.

For detailed descriptions of BGP configuration, see the “IP Routing Protocols” part of the Cisco IOS IP 
Configuration Guide, Release 12.2. For details about specific commands, see the Cisco IOS IP 
Command Reference, Volume 2 of 3: Routing Protocols, Release 12.2. See 

Appendix C, “Unsupported 

Commands in Cisco IOS Release 12.2(52)EY,”

 for a list of BGP commands that are visible but not 

supported by the switch.

Managing Routing Policy Changes

Routing policies for a peer include all the configurations that might affect inbound or outbound routing 
table updates. When you have defined two routers as BGP neighbors, they form a BGP connection and 
exchange routing information. If you later change a BGP filter, weight, distance, version, or timer, or 
make a similar configuration change, you must reset the BGP sessions so that the configuration changes 
take effect. 

There are two types of reset, hard reset and soft reset. The switch supports a soft reset without any prior 
configuration when both BGP peers support the soft route refresh capability, which is advertised in the 
OPEN message sent when the peers establish a TCP session. A soft reset allows the dynamic exchange 
of route refresh requests and routing information between BGP routers and the subsequent 
re-advertisement of the respective outbound routing table. 

•

When soft reset generates inbound updates from a neighbor, it is called dynamic inbound soft reset. 

•

When soft reset sends a set of updates to a neighbor, it is called outbound soft reset. 

Содержание 3845 - Security Bundle Router





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3845 - Security Bundle Router

Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Бренд: Lantronix Страницы: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Бренд: Lantronix Страницы: 7
Lantronix Maestro E220 Series Quick Start Manual preview
Maestro E220 Series
Бренд: Lantronix Страницы: 25
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Бренд: Garland Страницы: 6
Konica Minolta Network Setup Network Setup Manual preview
Network Setup
Бренд: Konica Minolta Страницы: 38
Western Digital My Net N750 Start Here Manual preview
My Net N750
Бренд: Western Digital Страницы: 8
IBM J02M Quick Start Manual preview
J02M
Бренд: IBM Страницы: 32
Jetter JetWeb JX2-PR0FI1 Operator'S Manual preview
JetWeb JX2-PR0FI1
Бренд: Jetter Страницы: 67
Oracle B31003-01 User Manual preview
B31003-01
Бренд: Oracle Страницы: 112
Supero 6027R-E1R12N User Manual preview
6027R-E1R12N
Бренд: Supero Страницы: 112
NETGEAR WGR614 - Wireless-G Router Wireless Reference Manual preview
WGR614 - Wireless-G Router Wireless
Бренд: NETGEAR Страницы: 116
ZyXEL Communications VMG5313-BXB SERIES Quick Start Manual preview
VMG5313-BXB SERIES
Бренд: ZyXEL Communications Страницы: 2
NETGEAR GSM7224v2 - Layer 2 Managed Gigabit Switch Datasheet preview
GSM7224v2 - Layer 2 Managed Gigabit Switch
Бренд: NETGEAR Страницы: 3
Lanner FW-7551 User Manual preview
FW-7551
Бренд: Lanner Страницы: 38
Allied Telesis AT-BSTACK1 Quick Install Manual preview
AT-BSTACK1
Бренд: Allied Telesis Страницы: 34
Tripp Lite WEBCARDLX Owner'S Manual preview
WEBCARDLX
Бренд: Tripp Lite Страницы: 34
Tenda DH301 User Manual preview
DH301
Бренд: Tenda Страницы: 120
ALIBI ALI-NVR71128R User Manual preview
ALI-NVR71128R
Бренд: ALIBI Страницы: 232

Бренды по названию

Популярные бренды

Загрузить еще бренды