manualshive.com logo in svg

Cisco 3845 - Security Bundle Router, Руководство пользователя программного обеспечения

Маршрутизатор Cisco 3845 - Security Bundle Router является надежным и безопасным решением для вашей сети. Скачайте бесплатно руководство по эксплуатации и программное обеспечение на {веб-сайт}, чтобы использовать его на максимуме. Узнайте все возможности и настройки вашего устройства.

Поделиться
Скачать
background image

 

27-25

Cisco ME 3800X and 3600X Switch Software Configuration Guide

OL-23400-01

Chapter 27      Configuring QoS

Configuring QoS

•

Egress classification for a class of traffic that has been acted on by an input policy-map can take 
place only on the per-hop behavior criteria and value established by the input policy-map. 

–

If a class in an input policy-map is classifying based on per-hop behavior criteria and is 
configured for policing but not marking, then the per-hop behavior established by the input 
policy-map for that class of traffic is the classification criteria and value in the associated 
class-map. 

–

If a class in an input policy-map is not classifying on per-hop behavior criteria, but is classifying 
on flow criteria by using a MAC ACL or IP ACL, and it is configured for policing, a default 
best-effort per-hop behavior is established for that class of traffic. Traffic in this class is not 
eligible for egress classification based on per-hop behavior criteria.

–

If a class in an input policy-map is configured for marking, the per-hop behavior established by 
the input policy-map for that class of traffic is the marked per-hop behavior criteria and value.   

–

If a class in an input policy-map is not configured for any action (class-default), a default 
best-effort per-hop behavior is established for that class of traffic. Traffic in this class is not 
eligible for egress classification based on PHB-criteria.

For example: if the per-hop behavior established for a class of traffic by an input policy-map is 
DSCP ef, you can classify that class of traffic on the egress based only on DSCP ef and not on any 
other mutually exclusive per-hop behavior such as outer CoS or inner CoS. 

•

Egress classification on a target with no input policy map attached can use any classification criteria 
specified in the egress policy. When an input policy map is attached to a target, even if traffic does 
not match any classes in the input policy, it cannot be egress-classified.

•

When configuring both MPLS VPN and QoS, you can apply most QoS functions to MPLS VPN 
traffic. However, for a hierarchical QoS function, you cannot apply a service policy that would 
match traffic on a per-VRF basis because VRFs are dynamically assigned to an MPLS label. For 
MPLS VPN traffic, you can apply a service-policy on egress traffic that matches traffic based on 
DSCP or MPLS. For information about configuring QoS with MPLS and EoMPLS, see the 

“Configuring MPLS and EoMPLS QoS” section on page 27-53

.

•

T

here is a limitation per bridge-domain on the number of unique flows classified on inner or outer 

VLANs that you can configure for egress classification. An error message appears when this 
limitation is exceeded.

•

Hierarchical marking and policing are not supported. You can configure marking and policing for 
any number of classes on any one of the three levels of the policy-map hierarchy. If you configure 
marking on one level, you can configure policing without marking (transmit, drop) on another level. 

•

An EFP can support only 2-level egress scheduling policies. If you attach a 3-level hierarchical 
policy to an EFP, only 2 of the 3 levels can have scheduling actions (bandwidth, shape, or priority)

•

There is a limitation on the maximum number of unique per-hop behavior-criteria combinations that 
can be configured on the system. The limit is internally calculated and is a function of input 
classification, marking, and egress classification based on per-hop behavior. An error message 
appears when this limit is reached.

Configuring Input Policy Maps

•

Configuring Input Class Maps, page 27-26

•

Using ACLs to Classify Traffic, page 27-28

•

Configuring Class-Based Marking, page 27-32

•

Configuring Policing, page 27-34

Содержание 3845 - Security Bundle Router





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3845 - Security Bundle Router

Vonets MINI300 Quick Setting Manual preview
MINI300
Бренд: Vonets Страницы: 8
Multitech MultiConnect SE MTS2EA Specification Sheet preview
MultiConnect SE MTS2EA
Бренд: Multitech Страницы: 2
U.S. Products maxg Quick Installation Manual preview
maxg
Бренд: U.S. Products Страницы: 80
Enertronica Santerno SINUS H PROFInet User Manual preview
SINUS H PROFInet
Бренд: Enertronica Santerno Страницы: 34
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Бренд: Internet Security Systems Страницы: 42
3Com 3C8567 - SuperStack II NETBuilder SI 567... Datasheet preview
3C8567 - SuperStack II NETBuilder SI 567...
Бренд: 3Com Страницы: 6
Raven RFMOW V2 User Manual preview
RFMOW V2
Бренд: Raven Страницы: 33
Modecom MC-421 Quick Installation Manual preview
MC-421
Бренд: Modecom Страницы: 16
ADC HiGain H4TU-R-402 List 5A Quick Installation preview
HiGain H4TU-R-402 List 5A
Бренд: ADC Страницы: 7
NetCommWireless NTC-220 Series Quick Start Manual preview
NTC-220 Series
Бренд: NetCommWireless Страницы: 28
Idis DR-8516 Installation Manual preview
DR-8516
Бренд: Idis Страницы: 28
Gbord EN-203 User Manual preview
EN-203
Бренд: Gbord Страницы: 11
Wieland wienet UMS 5-L Installation Instruction preview
wienet UMS 5-L
Бренд: Wieland Страницы: 2
IEI Technology PUZZLE-5030 User Manual preview
PUZZLE-5030
Бренд: IEI Technology Страницы: 119
Hanwha Vision XRN-3210B4 User Manual preview
XRN-3210B4
Бренд: Hanwha Vision Страницы: 131
UltrArmor UA3 Series User Manual preview
UA3 Series
Бренд: UltrArmor Страницы: 3
UfiSpace S9601-104BC Hardware Installation Manual preview
S9601-104BC
Бренд: UfiSpace Страницы: 34
ubiquoss U9016B Installation Manual preview
U9016B
Бренд: ubiquoss Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды