Cisco 12000 - Series Chassis Modular Expansion Base Скачать руководство пользователя | Manualshive

Страница: 15 / 132

background image

xv

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Preface

Objectives

Objectives

This document describes the SPA Interface Processors (SIPs) and shared port adaptors (SPAs) that are
supported on the Cisco 12000 series routers. This document also describes how to install the supported
SIPs and SPAs and how to troubleshoot the installation.

Organization

This document contains the following chapters:

Related Documentation

This section refers you to other documentation that also might be useful as you configure your
Cisco xxxx series router. The documentation listed below is available online.

•

Cisco 12000 Series Router SIP and SPA Software Configuration Guide (Cisco IOS)

•

Cisco IOS Release Notes for Cisco 12000 Series Routers

•

Regulatory Compliance and Safety Information for Cisco 12000 Series Routers

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.

Section

Title

Description

Chapter 1

Overview: Cisco 12000 Series
Router SPA Interface Processors

Provides a SIP/SPA compatibility summary. For
each supported SIP, provides a summary of SIP
characteristics and a SIP overview.

Chapter 2

Overview: Cisco 12000 Series
Router Shared Port Adapters

For each supported SPA, provides a summary of
SPA characteristics and a SPA overview.

Chapter 3

Preparing to Install a SPA Interface
Processor or a Shared Port Adapter

Describes the required tools, equipment, and
safety guidelines for installing SIPs and SPAs.

Chapter 4

Installing and Removing a SPA
Interface Processor

Describes the procedures for installing and
removing a SIP on a Cisco 12000 series router.

Chapter 5

Installing and Removing a Shared
Port Adapter

Describes the procedures for installing and
removing a SPA on a Cisco 12000 series router. It
also describes how to verify the SIP and SPA
installation.

Chapter 6

Troubleshooting the Installation

Provides information for troubleshooting the
installation of SIPs and SPAs. It also describes
helpful debug commands and error messages.

«
...
13
14
15
16
17
...
»

Содержание 12000 - Series Chassis Modular Expansion Base





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

OfficeConnect 1600

Бренд: 3Com Страницы: 8

Бренд: 3Com Страницы: 8

Бренд: LORD Страницы: 9

Бренд: D-Link Страницы: 83

PG-FLEX RT FRL-752

Бренд: PairGain Страницы: 6

Бренд: Patton electronics Страницы: 145

CyberSWITCH CSX101

Бренд: Cabletron Systems Страницы: 72

Бренд: B+B SmartWorx Страницы: 50

Бренд: Cradlepoint Страницы: 2

Бренд: ZyXEL Communications Страницы: 8

Бренд: Tripp Lite Страницы: 3

Routers and Switches

Бренд: Allied Telesis Страницы: 15

Dimension GS-2024

Бренд: ZyXEL Communications Страницы: 266

Бренд: Airaya Страницы: 28

I-FLY A02-WRA4-54G

Бренд: Atlantis Land Страницы: 3

Бренд: Tachosys Страницы: 15

Бренд: Adeunis RF Страницы: 68

Бренд: Lobaro Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды