Cisco 12000 - Series Chassis Modular Expansion Base Скачать руководство пользователя

Страница: 70 / 132

2-28

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters

1-Port Channelized STM-1/OC-3 SPA Overview

1-Port Channelized STM-1/OC-3 SPA LEDs

The 1-Port Channelized STM-1/OC-3 SPA has two types of LEDs: an A/L LED for each port and a
STATUS LED, as shown in

Figure 2-15

Figure 2-15 1-Port Channelized STM-1/OC-3 SPA Faceplate

The 1-Port Channelized STM-1/OC-3 SPALEDs are described in

Table 2-5

1-Port Channelized STM-1/OC-3 SPA Interface Specifications

The framer processes incoming and outgoing SONET or SDH frames. The framer operates at
OC-3c/STM-1 line rates (155.52 Mbps).

Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP])
and is mapped into the STS-3c/STM-1 frame.

C/A (Carrier/Alarm) LED

STATUS LED

A/L (Active Loopback) LED

SPA-1XCHSTM1/OC3

ATUS

138847

C/A

A/L

Table 2-25 1-Port Channelized STM-1/OC-3 SPA LEDs

LED Label

Color

State

Meaning

C/A

Off

Port is not enabled by software.

Green

Port is enabled by software, and there is a valid T3 signal
without any alarms.

Amber

Port is enabled by software, and there is at least one alarm.

A/L

Off

Port is not enabled by software.

Green

Port is enabled by software, loopback is off.

Amber

Port is enabled by software, loopback is on.

STATUS

Off

SPA power is off.

Green

SPA is ready and operational.

Amber

SPA power is on and good, and SPA is being configured.

Содержание 12000 - Series Chassis Modular Expansion Base





































































































































Результаты поиска

Содержание 12000 - Series Chassis Modular Expansion Base

Отзывы:

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

Бренды по названию

Популярные бренды

Cisco 12000 - Series Chassis Modular Expansion Base, Руководство по установке оборудования

Результаты поиска

Содержание 12000 - Series Chassis Modular Expansion Base

Отзывы:

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

Бренды по названию

Популярные бренды