Cisco 12000 - Series Chassis Modular Expansion Base Скачать руководство пользователя | Manualshive

Страница: 79 / 132

background image

2-37

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters

1-Port OC-192c/STM-64 POS RPR XFP SPA Overview

Figure 2-23 SPA Mate Cables

Note

The RPR mate cable is only necessary when the SPA is to be used in RPR mode. It is not needed in POS
mode. Support for the RPR feature is dependent on the platform software release feature content. Verify
support for the RPR feature support by reviewing the relevant SPA datasheets or by contacting your
Cisco representative.

1-Port OC-192c/STM-64 POS RPR XFP SPA Overview

The 1-Port OC-192c/STM-64 POS/RPR XFP SPA is a single-height SPA that is installed in one SIP
subslot. The 1-Port OC-192c/STM-64 POS/RPR XFP SPA provides SONET and SDH network
connectivity with a bandwidth of 9.95 Gbps.

For more information about SPA bandwidth, see the

“Bandwidth Oversubscription”

section in this

chapter. For more information about SPAs and their compatibility with SIPs and modular optics, see the
product overview chapter in this guide.

The 1-Port OC-192c/STM-64 POS/RPR XFP SPA uses a 10-Gbps small form-factor pluggable optical
receptacle for each port allowing connection to single-mode optical fiber. For more information on the
optical fiber cables used with this SPA, see the

“1-Port OC-192c/STM-64 POS/RPR SPA Fixed Optical

Transceiver, 40-Pin Connector, and Cables” section on page 2-36

.

The following sections describe the 1-Port OC-192c/STM-64 POS/RPR XFP SPA:

•

1-Port OC-192c/STM-64 POS/RPR SPA LEDs, page 2-34

•

1-Port OC-192c/STM-64 POS/RPR SPA Interface Specifications, page 2-35

•

1-Port OC-192c/STM-64 POS/RPR SPA Fixed Optical Transceiver, 40-Pin Connector, and Cables,
page 2-36

1

Long length RPR mate cable for single port
RPR SPAs (CBL-RPR-OC192-L)

2

Short length RPR mate cable for single port
RPR SPAs (CAB-RPR-OC192-S)

129198

1

2

«
...
77
78
79
80
81
...
»

Содержание 12000 - Series Chassis Modular Expansion Base





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 32

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: Tripp Lite Страницы: 2

ADSL 2/2+ Router with USB Port ADE-3410v2

Бренд: Planet Страницы: 62

Бренд: Abocom Страницы: 2

LonWorks Communication Module LN-01

Бренд: Delta Electronics Страницы: 1

Бренд: Keysight Technologies Страницы: 106

Бренд: Perle Страницы: 4

Бренд: Camozzi Страницы: 22

Бренд: Billion Страницы: 158

Gen3 Ethernet Module

Бренд: NCD Страницы: 18

Бренд: 3Com Страницы: 63

Бренд: Martin Страницы: 41

IE-SW-AL18M-16TX-2GC

Бренд: Weidmüller Страницы: 2

ROUTE FINDER RFIPSC-1

Бренд: Multitech Страницы: 54

I-FLY A02-WRA4-54G

Бренд: Atlantis Land Страницы: 3

DHI-NVR5208-4KS2

Бренд: Dahua Страницы: 361

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды