Cisco 12000 - Series Chassis Modular Expansion Base Скачать руководство пользователя

Страница: 32 / 132

1-12

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 1 Overview: Cisco 12000 Series Router SPA Interface Processors

Cisco 12000 SIP-401 Overview

Figure 1-10 Cisco 12000 SIP-401 Face Plate

The Cisco 12000 SIP-401 LEDs are described in

Table 1-10

Cisco 12000 SIP-401 Physical Specifications

The Cisco 12000 SIP-401

physical specifications are shown in the following table.

SPA Slot Numbering on the Cisco 12000 SIP-401

The Cisco 12000 SIP-401 accepts 4 single-width, single-height SPAs.

SPA subslot 0

Ejector Levers

SPA subslot 1

Status LED

SPA subslot 2

Rate LED

SPA subslot 3

12000-SIP-400

158211

Table 1-10

Cisco 12000 SIP-401 LED

LED Label

Color

State

Meaning

Status

Yellow

IOS is loaded and SIP is ready to be enabled.

Green

SIP is active.

Rate

Off

SIP is SIP-401 or SIP-501.

Green

SIP is SIP-601.

Table 1-11

Cisco 12000 SIP-401 Physical Specifications

Description

Specifications

Physical dimensions

Occupies one line card slot on a Cisco 12000 Series Router

Shipping weight

10 kg

Operating temperature

32 to 104°F (0 to 40°C)

Relative humidity

10 to 90 percent, noncondensing

Storage temperature

–4 to 149°F (–20 to 65°C)

Содержание 12000 - Series Chassis Modular Expansion Base





































































































































Результаты поиска

Содержание 12000 - Series Chassis Modular Expansion Base

Отзывы:

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

Бренды по названию

Популярные бренды

Cisco 12000 - Series Chassis Modular Expansion Base, Руководство по установке оборудования

Результаты поиска

Содержание 12000 - Series Chassis Modular Expansion Base

Отзывы:

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

Бренды по названию

Популярные бренды