Cisco 12000 - Series Chassis Modular Expansion Base Скачать руководство пользователя | Manualshive

Страница: 87 / 132

background image

2-45

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters

2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA, 4-Port OC-3c/STM-1 POS SPA, and 8-Port

Note

Three different faceplates exist for either the 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and
OC-12c/STM-4 POS SPAs. They each contain the same LEDs and the number of ports are 2, 4 and 8
respectively.

Figure 2-29 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA

Faceplate

The 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA and the 4-Port and 8-Port
OC-3c/STM-1 POS SPA LEDs are described in

Table 2-31

.

2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA and 4-Port
and 8-Port OC-3c/STM-1 POS SPA Interface Specifications

The framer processes incoming and outgoing SONET or SDH frames. The framer operates at OC-3 line
rates (155.52 Mbps) and OC-12 line rates (622.08 Mbps). Packet data is transported with a
user-configured encapsulation (such as Point-to-Point Protocol [PPP]) and is mapped into the layer 2
frame.

The 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA and the 4-Port and 8-Port
OC-3c/STM-1 POS SPA interface complies with the following IETF RFCs:

1

C/A (Carrier/Alarm) LED

3

STATUS LED

2

A/L (Active Loopback) LED

ST

ATUS

SP

A-8XOC12-POS

138896

3

3

C/A

A/L

0

C/A

A/L

1

C/A

A/L

2

C/A

A/L

2

1

4

C/A

A/L

5

C/A

A/L

6

C/A

A/L

7

C/A

A/L

Table 2-31 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA and 4-Port and 8-Port

OC-3c/STM-1 POS SPA LEDs

LED Label

Color

State

Meaning

C/A

Off

Off

SONET controller is shut down.

Green

On

Port is enabled by software, and there is a valid SONET signal
without any alarms.

Amber

On

Port is enabled by software, and there is at least one alarm.

A/L

Off

Off

Interface is shut down.

Green

On

Port is enabled by software, loopback is off.

Amber

On

Port is enabled by software, loopback is on.

STATUS

Off

Off

SPA power is off.

Green

On

SPA is ready and operational.

Amber

On

SPA power is on and good; SPA is being configured.

«
...
85
86
87
88
89
...
»

Содержание 12000 - Series Chassis Modular Expansion Base





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

Бренд: D-Link Страницы: 100

Бренд: D-Link Страницы: 134

Бренд: D-Link Страницы: 187

Бренд: D-Link Страницы: 225

Бренд: D-Link Страницы: 31

Бренд: D-Link Страницы: 35

DES-1016D - Switch

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 107

AirPlusXtremeG DI-624

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 48

Бренд: Vanguard Страницы: 121

Бренд: Magnadyne Страницы: 13

Бренд: F5 Страницы: 72

Бренд: Edge-Core Страницы: 7

Wireless Mini PCI Module

Бренд: E-Tech Страницы: 42

Бренд: I-O Wireless Страницы: 55

Бренд: Davey Страницы: 18

Бренд: XMOS Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды