Cisco 12000 - Series Chassis Modular Expansion Base Скачать руководство пользователя | Manualshive

Страница: 71 / 132

background image

2-29

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters

1-Port Channelized STM-1/OC-3 SPA Overview

The 1-Port Channelized STM-1/OC-3 SPA interface is compliant with RFC 1619,

PPP over

SONET/SDH

, and RFC 1662,

PPP in HDLC-like Framing

. The 1-Port Channelized STM-1/OC-3 SPA

also provides support for SNMP v1 agent (RFC 1155–1157), and Management Information Base (MIB)
II (RFC 1213).

1-Port Channelized STM-1/OC-3 SPA Cables and Connectors

The 1-Port Channelized STM-1/OC-3 SPA uses a small form-factor pluggable (SFP) optical transceiver
module installed in each port for SONET and SDH single-mode and multimode optical fiber connection
(see

Figure 2-16

).

Figure 2-16 SFP Optics Module

The SFP optical transceiver modules used with the 1-Port Channelized STM-1/OC-3 SPA provide the
following optical fiber options:

•

Multimode—155-Mbps, OC-3c/STM-1 optical fiber (SONET STS-3c or SDH STM-1)

Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns.

•

Single-mode—155-Mbps, OC-3c/STM-1 optical fiber (SONET STS-3c or SDH STM-1)

Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns. (Nominal
diameter is approximately 10/125 microns.)

For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable (see

Figure 2-17

) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX).

Use single-mode (for intermediate- or long-reach configurations) or multimode optical fiber cable to
connect your router to a network or to connect two 1-Port Channelized STM-1/OC-3 SPA-equipped
routers back to back.

Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected
back-to-back without using an attenuator between the two of them.

127158

«
...
69
70
71
72
73
...
»

Содержание 12000 - Series Chassis Modular Expansion Base





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

Бренд: Makita Страницы: 2

Бренд: Aastra Страницы: 2

Бренд: Patton electronics Страницы: 51

Бренд: Quick Eagle Networks Страницы: 4

Бренд: Conceptronic Страницы: 2

Бренд: Opengear Страницы: 2

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

Бренд: TP-Link Страницы: 176

Бренд: Cisco MERAKI Страницы: 4

Бренд: BWI Страницы: 5

SinoCon C2000-C2-SHK0401-BB1

Бренд: KonNad Страницы: 12

Бренд: BEC Страницы: 159

Бренд: Tripp Lite Страницы: 2

Бренд: OneAccess Страницы: 47

Бренд: NETGEAR Страницы: 152

Бренд: Zhone Страницы: 53

Бренд: NETGEAR Страницы: 20

GlobeSurfer X-1

Бренд: Option Audio Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды