Cisco 12000 - Series Chassis Modular Expansion Base Скачать руководство пользователя | Manualshive

Страница: 113 / 132

background image

5-7

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 5 Installing and Removing a Shared Port Adapter

Checking the Installation

When you reinsert the SIP, the system automatically brings up the interfaces that were up

when the SIP was removed.

Router#

18:05:00: %OIR-6-INSCARD: Card inserted in slot 3, interfaces administratively shut down

18:05:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3/0, changed state

to up

Note

When a new SIP is inserted or when a SIP is moved to a new slot, the system recognizes the new
interfaces but leaves them in the shutdown state until you configure them and change their state to up.

The following sample display shows the events logged by the system as you insert a

new

SIP in module

slot 3.

Router#

18:05:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3/1, changed state

to down

Use the following procedure to verify that the SIP is installed correctly:

Step 1

Observe the console display messages and verify that the system discovers the SIP, while the system
reinitializes each interface, as follows:

•

If you installed a new SIP, the STATUS LED should be on (green). The system should recognize all
new interfaces but leave them configured as

down

.

•

If you replaced a SIP, the STATUS LED should be on (green). The system does not recognize each
interface and places it in the administratively down state.

Step 2

Verify that the ENABLED LED on the SPA goes on (is green) and remains on after the reinitialization
is complete. If the ENABLED LED remains on, proceed to

Step 5

. If the ENABLED LED does not

remain on, proceed to

Step 3

.

Step 3

If the ENABLED LED on a SPA fails to go on, the SPA or the SIP might not be fully seated

even if the

SPA lock is in the locked and horizontal position

. When a SPA is not recognized, the SIP is deactivated,

and its OIR LED is yellow.

•

Remove the SIP from the router.

•

Remove the SPA from the SIP.

•

Inspect the SIP and the SPA. Verify there are no bent pins or parts and that there is nothing lodged
in the two devices that could prevent a good connection.

•

Insert the SPA in the SIP by sliding the SPA all the way in the SIP until the SPA is firmly seated in
the SPA interface connector. When fully seated in the SIP, the SPA might be slightly behind the SIP
faceplate.

•

Insert the SIP into the router.

•

After the system reinitialization, the ENABLED LED on the SPA should go on and remain on. If the
ENABLED LED remains on, proceed to

Step 5

. If it does not, proceed to

Step 4

.

Step 4

If the ENABLED LED on a SPA still fails to go on, remove the SIP and install it in another available slot
on the router.

•

If the ENABLED LED goes on, suspect a failed backplane port in the original slot.

•

If the ENABLED LED fails to go on, remove the SIP and ensure the SPA is firmly seated in its slot.
Remove and reinstall it accordingly.

«
...
111
112
113
114
115
...
»

Содержание 12000 - Series Chassis Modular Expansion Base





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

Бренд: X-Micro Страницы: 74

Бренд: Ubiquiti Страницы: 23

Бренд: Axis Страницы: 104

Бренд: Maipu Страницы: 80

Бренд: WAGO Страницы: 2

AirStation WZR-1166DHP

Бренд: Buffalo Страницы: 2

Бренд: Supero Страницы: 54

RuggedNet 10G/Si

Бренд: OST Страницы: 8

ForeFront 2616RC

Бренд: Patton electronics Страницы: 80

Бренд: AMCI Страницы: 55

Firebox T85-PoE

Бренд: Watchguard Страницы: 27

FrameSaver DSL 9783 CSU/DSU

Бренд: Paradyne Страницы: 233

Бренд: Nokia Страницы: 3

Бренд: Nokia Страницы: 2

Бренд: Nokia Страницы: 2

Бренд: Nokia Страницы: 2

Бренд: Nokia Страницы: 3

Бренд: Nokia Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды