Cisco 12000 - Series Chassis Modular Expansion Base Скачать руководство пользователя | Manualshive

Страница: 74 / 132

background image

2-32

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters

1-Port OC-48c/STM-16 POS SPA Overview

•

RFC 2615,

PPP over SONET/SDH

•

RFC 1662,

PPP in HDLC-like Framing

RFC 2615,

PPP over SONET/SDH

The 1-Port OC-192c/STM-64 POS/RPR XFP SPA also provides

support for SNMP v1 agent (RFC 1155–1157) and RFC 1213:

•

RFC 1155,

Structure and Identification of Management Information for TCP/IP-based Internets

•

RFC 1156,

Management Information Base for Network Management of TCP/IP-Based Internets

•

RFC 1157,

Simple Network Management Protocol (SNMP)

•

RFC 1213,

Management Information Base (MIB) for Network Management of TCP/IP-Based

Internets:MIB II

.

1-Port OC-48c/STM-16 POS SPA Optical Transceiver Modules, Connectors, and
Cables

The 1-Port OC-48c/STM-16 POS SPA uses a single-mode, 9.95 Gbps, OC-48 optical fiber (SONET
STS-48) optical transceiver module for SONET connection to the network.

The 1-Port OC-48c/STM-16 POS SPA supports the following type of optical transceiver module:

•

Single-mode short reach (SR) SFP module—SFP-OC48-SROC-48c/STM-16c

•

Single-mode intermediate reach (IR) SFP module—SFP-OC48-IR1OC-48c/STM-16c

•

Single-mode long reach (LR) SFP module—SFP-OC48-LR2OC-48c/STM-16c

Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter
is approximately 10/125 microns) to connect your router to a network.

Figure 2-25

shows the cable type for use with the XFP optical transceiver module on the

1-Port OC-48c/STM-16 POS SPA.

Figure 2-19 LC-Type Cable for the SFP Optical Transceiver Modules

Note

The 40-pin connector on the 1-Port OC-48c/STM-16 POS SPA is used for resilient packet ring (RPR)
connections.

Mate Interface Cables

The 1-Port OC-48c/STM-16 POS SPA supports two mate interface configurations:

•

Mate between two OC-48c SPAs in the same SIP

/ /

/ /

/ /

TX

RX

84929

«
...
72
73
74
75
76
...
»

Содержание 12000 - Series Chassis Modular Expansion Base





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000 - Series Chassis Modular Expansion Base

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Бренд: D-Link Страницы: 31

Бренд: Rosewill Страницы: 3

Бренд: SurfControl Страницы: 2

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: TRENDnet Страницы: 2

Бренд: TP-Link Страницы: 25

Бренд: ATCOM Страницы: 18

SA-REP-ETHERLINK_II-1DA-PL

Бренд: S-Access Страницы: 106

Бренд: ICP DAS USA Страницы: 60

Бренд: NetComm Страницы: 2

Бренд: MTI Страницы: 41

Бренд: Billion Страницы: 2

Бренд: Cambium Networks Страницы: 292

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды