Circor HOUTTUIN TT Twin-Screw Скачать руководство пользователя страница 7

Страница: 7 / 78

Introduction and Safety

TT Twin-Screw Pump -

Installation, Operation & Maintenance Manual

Hazard categories

Hazard categories can either fall under hazard levels or let specific symbols replace the

ordinary hazard level symbols.

Electrical hazards are indicated by the following specific symbol:

Electrical Hazard:

These are examples of other categories that can occur. They fall under the ordinary hazard

levels and may use complementing symbols:

•

Crush hazard

•

Cutting hazard

•

Arc flash hazard

The Ex symbol

The Ex symbol indicates safety regulations for Ex-approved products when used in

atmospheres that are potentially explosive or flammable.

Environmental safety

The work area

Always keep the station clean to allow early discovery of any emissions due to a malfunction.

Waste and emissions regulations

Observe these safety regulations regarding waste and emissions:

•

Appropriately dispose of all waste.

•

Handle and dispose of the processed liquid in compliance with applicable environmental

regulations.

•

Clean up all spills in accordance with safety and environmental procedures.

•

Report all environmental emissions to the appropriate authorities.

WARNING:

If the product has been contaminated in any way, such as from toxic/flammable chemicals or
biological agents do NOT send the product to CIRCOR unless it has been properly
decontaminated.

Electrical installation

For electrical installation recycling requirements, consult your local electric utility.

Recycling guidelines

Always follow local laws and regulations regarding recycling.

Содержание HOUTTUIN TT Twin-Screw















































































Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды

Circor HOUTTUIN TT Twin-Screw, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды