Circor HOUTTUIN TT Twin-Screw Скачать руководство пользователя страница 70

Страница: 70 / 78

Disassembly, Inspection & Reassembly

Twin-Screw Pump -

Installation, Operation, and Maintenance Manual

21. Install key (132) on the gear side idler shaft and install the gearwheel (109) and secure it

with locknut (110).

22. Install, tighten and align gearwheel (108) along with the ring feder (113) to the shaft (101)

gear side using hex head screw (114).

23. Rotate drive shaft (101) manually 360° and check for free rotation, inspect the shaft

clearances to meet the target value. Tight scrub screw incase for Cartridge seal after

shaft alignment.

24. Install gearbox (406) with gasket (440) against the cover DF using hex head bolt (338).

25. Install bush (725) on drive shaft (101) with Loctite 243.

26. Install o- ring (448) to bearing covers (409) (410) and install it into cover D (407) using

the hex head screw (433).

27. Install lip seal (704) at the drive shaft position (101) and fill the bearing covers (409) (410)

with grease.

28. Close all drain ports using a plug (342) & (382) with fiber washer (343) & (383).

29. Close all pressure monitoring port using plug (382) with fiber washer (383) if not used for

measuring.

30. Fill the gearbox (406) with the correct oil to the center of the sight glass and close the

filling port with reducing socket (445) and breather (444).

31. For integrated PRV, install valve seat ring (543) into the case (350) and place the right

spring length (550).

32. Install o- ring (545) on the guide rod (554) and install the preassembled guide rod to

spring disc (551).

33. Install the preassembled guide rod (554) with spring disc (551) and gasket (575) into

spring cap (506) and install the sub-assembly to the case (350) using the hex head screw

(338).

34. Preload the spring according to the design data. The final settings will be done during the

pump performance test.

35. Close all support threads or bores with permanent plugs.

36. Check for oil leaks and correct oil levels.

Содержание HOUTTUIN TT Twin-Screw















































































Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды

Circor HOUTTUIN TT Twin-Screw, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды