Circor HOUTTUIN TT Twin-Screw Скачать руководство пользователя страница 9

Страница: 9 / 78

Introduction and Safety

TT Twin-Screw Pump -

Installation, Operation & Maintenance Manual

Precautions during work

Observe these safety precautions when you work with the product or are in connection with

the product:

CAUTION:

Failure to observe the instructions contained in this manual could result in personal injury and
property damage and may void the warranty. Read this manual carefully before installing and
using the product.

•

Always wear the appropriate PPE.

•

Never work alone.

•

Stay well clear of suspended loads.

•

Always lift the product by its lifting device(s).

•

Beware of the risk of a sudden start if the product is used with an automatic control.

•

Rinse the components in water or a solvent as directed after you disassemble the pump.

•

Never exceed the maximum working pressure of the pump.

•

Never disable, remove or bypass the pump safety pressure relief valve

•

Do not open any vent or drain valve or remove any plugs while the system is pressurized.

Make sure that the pump is isolated from the system and that pressure is relieved before

you disassemble the pump, remove plugs, or disconnect piping.

•

Never operate a pump without a properly installed coupling guard.

•

The coupling guard used in an ATEX classified environment must be constructed from

a non-sparking material.

Airborne Noise

Airborne Noise of the pump is dependent on the application parameters and where it

exceeds 70 dB(A)

appropriate safety measures must be taken to prevent injury. The specific sound

pressure level of each pump is included in a datasheet provided to the customer along with this

manual.

Hazardous liquids

The product is designed for use in liquids that can be hazardous to your health. Observe

these rules when you work with the product:

•

Make sure that all personnel who work with biologically hazardous liquids are vaccinated

against diseases to which they may be exposed.

•

Observe strict personal cleanliness.

•

A small amount of liquid will be present in certain areas like the seal chamber and

cavities which cannot be fully drained due to the pump geometry.

Содержание HOUTTUIN TT Twin-Screw















































































Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды

Circor HOUTTUIN TT Twin-Screw, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды