Circor HOUTTUIN TT Twin-Screw Скачать руководство пользователя страница 20

Страница: 20 / 78

Transportation and Storage

Twin-Screw Pump -

Installation, Operation & Maintenance Manual

Baseplate-mounted units have lifting points for use with proper lifting devices. These lifting

points should be utilized as instructed on the unit GA or outline drawing

Figure 2: Example of the proper lifting method for baseplate-mounted units with a driver

Storage guidelines

Long-term storage

Units are shipped on skids and suitably boxed or crated to prevent damage from normal

handling. All exterior, unpainted surfaces subject to corrosion are coated with a rust preventive

compound. Pump openings are covered with blank flanges or special covers.

A packing list is furnished itemizing the contents of the shipment. When received, check the

contents against the packing list. Report any discrepancies to CIRCOR or your local CIRCOR

distributor immediately.

If pump is not to be immediately installed and operated and will be stored for more than 6

months, or if pump is not to be operated for some time after installation, the unit must be cared

for as follows:

Содержание HOUTTUIN TT Twin-Screw















































































Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды

Circor HOUTTUIN TT Twin-Screw, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды