Circor HOUTTUIN TT Twin-Screw Скачать руководство пользователя страница 62

Страница: 62 / 78

Disassembly, Inspection & Reassembly

Twin-Screw Pump -

Installation, Operation, and Maintenance Manual

4. Remove the locknut (110) and ringfeder screws (114) to loosen the both spur gears (108

& 109) from the shafts (101 & 102).

5. Remove the spur gears (108 & 109) from the shafts (101 & 102). Remove the key (132) if

necessary from the short shaft (102).

6. Remove the distance bush (124) from the gear side short shaft (102) and locknut (111)

on the gear side long shaft.

7. Remove nuts (311) which secure the bearing cover DF (401) to the casing (350).

8. Carefully remove the screws (338) which secure the bearing cover DF (401) to the

intermediate cover (419).

9. Remove bearing cover DF (401) from the intermediate cover (419) using jacking tap

holes available in cover DF (401). Oil seals (704) and bearings (105) will remain in

bearing cover DF (401).

10. Loosen the hex head screw (433) which secure the cover KA (409) & (410) to bearing

cover D (407). Lip seal (704) will remain in bearing cover D (407).

11. Carefully remove the nuts (338) which secure the bearing cover D (407) to the

intermediate cover (419).

12. Remove bearing cover D (407) from the intermediate cover (419) using jacking tap holes

available in cover D (407). Oil seals (704) and bearings (105) will remain in bearing cover

D (407).

13. Remove the hex head screw (471) which secure the seal cover (470) to the intermediate

cover (419) on both sides.

14. Remove the socket head screws (315) on the both sides which secure the intermediate

cover to the casing (350).

15. Use jacking tap holes available in intermediate cover (419) to remove completely from

the casing (350).

16. Remove the mechanical seal (702) from the shafts (101) & (102) by loosening the grub

screws available on the mechanical seal on both sides.

17. In case of cartridge seal, remove cartridge seal (702) from the intermediate cover (419)

by loosening the hex head screw (471).

18. Carefully remove the shaft (101) & (102) with screw blocks (100) simultaneously out of

the casing (350)

19. To remove the relief valve assembly, once again make sure that guide rod and spring are

free from compression.

20. Remove the hex head screw (338) which secure the spring cap (506) to the casing (350).

21. Remove inner races of roller bearings from shafts (101) & (102) or cover D and Cover

DF.

22. Remove all gaskets (440) & (575) and bush (726) as necessary.

Содержание HOUTTUIN TT Twin-Screw















































































Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды

Circor HOUTTUIN TT Twin-Screw, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды