Circor HOUTTUIN TT Twin-Screw Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 78

background image

Disassembly, Inspection & Reassembly

58

TT

Twin-Screw Pump -

Installation, Operation, and Maintenance Manual

Disassembly

Disassembly precautions

WARNING:

•

Failure to disconnect and lock out driver power may result in serious physical injury or
death. Always disconnect and lock out power to the driver before performing any
installation or maintenance tasks.

•

Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local rules.

•

Refer to driver/coupling/gear manufacturer's installation and operation manuals (IOM) for
specific instructions and recommendations.

•

Risk of serious personal injury. Applying heat to parts with internal cavities or reliefs can
cause trapped liquid to rapidly expand and result in a violent explosion. This manual
clearly identifies accepted methods for disassembling units. These methods must be
adhered to. Never apply heat to aid in part removal unless it is explicitly stated in this
manual

•

Handling heavy equipment poses a crush hazard. Use caution during handling and wear
appropriate Personal Protective Equipment (PPE, such as steel-toed shoes, gloves, etc.)
at all times.

•

Precautions must be taken to prevent physical injury. The pump may handle hazardous
and/or toxic fluids. Proper personal protective equipment should be worn. Pumpage must
be handled and disposed of in conformance with applicable environmental regulations.

•

Risk of serious physical injury or death from rapid depressurization. Ensure pump is
isolated from system and pressure is relieved before disassembling pump, removing
plugs, opening vent or drain valves, or disconnecting piping.

•

Risk of serious personal injury from exposure to hazardous or toxic liquids. A small
amount of liquid will be present in certain areas like the seal chamber upon disassembly..

CAUTION:

Avoid injury. Worn pump components can have sharp edges. Wear appropriate gloves while
handling these parts.

NOTICE:

This section of the IOM assumes that the user is trained and experienced in the assembly and
disassembly of heavy, precision, industrial rotating machinery.
**** If you have any doubts regarding your capabilities to follow the instructions while applying
appropriate levels of skill and care then please stop and seek assistance.****

Tools required

In order to disassemble the pump, you need these tools:

•

Brass drift punch

•

Cleaning agents and solvents

•

Dial indicators

«
...
58
59
60
61
62
...
»

Содержание HOUTTUIN TT Twin-Screw















































































Отзывы:

Нет отзывов

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренд: Jackco Страницы: 8

Бренд: EasyPro Страницы: 8

Бренд: Eaton Страницы: 29

Бренд: Clarke Страницы: 16

Бренд: Chiltrix Страницы: 54

Бренд: WilTec Страницы: 8

Бренд: Calorex Страницы: 44

AquaSurge PRO 2000-4000

Бренд: Aquascape Pro Страницы: 8

Бренд: York Страницы: 12

Бренд: Santon Страницы: 20

Clean Jet 800 Plus + Kit

Бренд: T.I.P. Страницы: 140

Бренд: T.I.P. Страницы: 72

Бренд: Whale Страницы: 64

Бренд: York Страницы: 8

Бренд: Samoa Страницы: 52

Gas Domestic Indoor Water Heater

Бренд: Rheem Страницы: 40

Бренд: SprayTECH Страницы: 20

AquaMax Eco Classic 3600

Бренд: Oase Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды