Circor HOUTTUIN TT Twin-Screw Скачать руководство пользователя страница 50

Страница: 50 / 78

Product Description

TT Twin-Screw Pump -

Installation, Operation & Maintenance Manual

• Running a pump without safety devices exposes operators to risk of serious personal injury

or death. Never operate a unit unless appropriate safety devices (guards, etc.) are properly
installed.

• Avoid death or serious injury. Assure mechanical seal guard is properly installed using

supplied fastening hardware.

• Failure to disconnect and lock out driver power may result in serious physical injury or

death. Always disconnect and lock out power to the driver before performing any installation
or maintenance tasks.

• Electrical connections must be made by certified electricians in compliance with all

international, national, state, and local rules.

• Refer to driver/coupling/gear manufacturer's installation and operation manuals (IOM) for

specific instructions and recommendations.

Bearing lubrication

Precautions

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. Ensure
That the bearings are properly lubricated prior to startup.

Pumps are shipped without oil

You must lubricate the NDE gears and bearings at the job site. The gear and bearing

housings are supplied with sight glasses. Make sure that the oil level is set to the center

of the sight glass when the pump is not running. (A false level reading can occur while

the pump is running).

Содержание HOUTTUIN TT Twin-Screw















































































Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды

Circor HOUTTUIN TT Twin-Screw, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HOUTTUIN TT Twin-Screw

Отзывы:

Похожие инструкции для HOUTTUIN TT Twin-Screw

Бренды по названию

Популярные бренды