Chrysler Pacifica 2021 Скачать руководство пользователя

Страница: 68 / 432

GETTING TO KNOW YOUR VEHICLE

2. Return to the vehicle and push the

programmed HomeLink® button three

times (holding the button for two seconds

each time). If the garage door opener motor

operates, programming is complete.

3. Push the programmed HomeLink® button

to confirm that the garage door opener

motor operates. If the garage door opener

motor does not operate, repeat the final

steps for the rolling code procedure.

Non-Rolling Code Garage Door Opener Final

Steps

1. Push and hold the programmed

HomeLink® button and observe the

HomeLink® indicator light. If the

HomeLink® indicator light stays on

constantly, programming is complete.

2. Push the programmed HomeLink® button

to confirm that the garage door opener

motor operates. If the garage door opener

motor does not operate, repeat the steps

from the beginning.

ROGRAMMING

OME

INK

® T

ISCELLANEOUS

EVICE

Refer to “Programming HomeLink® To A

Garage Door Opener” for the procedure on how

to program HomeLink® to a miscellaneous

device, as it follows the same procedure. Be

sure to determine if the device has a rolling

code, or non-rolling code before beginning the

programming process.

NOTE:

Canadian radio frequency laws require trans

mitter signals to time-out (or quit) after several

seconds of transmission, which may not be long

enough for HomeLink® to pick up the signal

during programming. Similar to this Canadian

law, some US gate operators are designed to

time-out in the same manner. The procedure

may need to be performed multiple times to

successfully pair the device to your HomeLink®

buttons.

EPROGRAMMING

A S

INGLE

OME

INK

® B

UTTON

To reprogram a single HomeLink® button that

has been previously trained, without erasing all

the channels, follow the procedure below. Be

sure to determine whether the new device you

want to program the HomeLink® button to has

a rolling code, or non-rolling code.

1. Place the ignition in the ON/RUN position,

without starting the engine.

2. Push and hold the desired HomeLink®

button until the HomeLink® Indicator light

begins to flash after 20 seconds. Do not

release the button.

WARNING!



Your motorized door or gate will open and

close while you are programming the

universal transceiver. Do not program the

transceiver if people or pets are in the path

of the door or gate.



Do not run your vehicle in a closed garage

or confined area while programming the

transceiver. Exhaust gas from your vehicle

contains Carbon Monoxide (CO) which is

odorless and colorless. Carbon Monoxide is

poisonous when inhaled and can cause you

and others to be severely injured or killed.

21_RUP_OM_EN_USC_t.book Page 66

Содержание Pacifica 2021

















































































































































































































































































































































































































































Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды

Chrysler Pacifica 2021, Руководство пользователя

Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды