Chrysler Pacifica 2021 Скачать руководство пользователя

Страница: 305 / 432

SAFETY

303

(Continued)

should remain in a forward-facing child seat with a

harness for as long as possible, up to the highest

weight or height allowed by the child seat.
All children whose weight or height is above the

forward-facing limit for the child seat should use a

belt-positioning booster seat until the vehicle’s

seat belts fit properly. If the child cannot sit with

knees bent over the vehicle’s seat cushion while

the child’s back is against the seatback, they

should use a belt-positioning booster seat. The

child and belt-positioning booster seat are held in

the vehicle by the seat belt.

Children Too Large For Booster Seats

Children who are large enough to wear the

shoulder belt comfortably, and whose legs are

long enough to bend over the front of the seat

when their back is against the seatback, should

use the seat belt in a rear seat. Use this simple

5-step test to decide whether the child can use

the vehicle’s seat belt alone:

1. Can the child sit all the way back against

the back of the vehicle seat?

2. Do the child’s knees bend comfortably over

the front of the vehicle seat – while the child

is still sitting all the way back?

3. Does the shoulder belt cross the child’s

shoulder between the neck and arm?

4. Is the lap part of the belt as low as possible,

touching the child’s thighs and not the

stomach?

5. Can the child stay seated like this for the

whole trip?

If the answer to any of these questions was

“no,” then the child still needs to use a booster

seat in this vehicle. If the child is using the lap/

shoulder belt, check seat belt fit periodically

and make sure the seat belt buckle is latched.

A child’s squirming or slouching can move the

belt out of position. If the shoulder belt contacts

the face or neck, move the child closer to the

center of the vehicle, or use a booster seat to

position the seat belt on the child correctly.

WARNING!



Improper installation can lead to failure of

an infant or child restraint. It could come

loose in a collision. The child could be badly

injured or killed. Follow the child restraint

manufacturer’s directions exactly when

installing an infant or child restraint.



After a child restraint is installed in the

vehicle, do not move the vehicle seat forward

or rearward because it can loosen the child

restraint attachments. Remove the child

restraint before adjusting the vehicle seat

position. When the vehicle seat has been

adjusted, reinstall the child restraint.



When your child restraint is not in use,

secure it in the vehicle with the seat belt or

LATCH anchorages, or remove it from the

vehicle. Do not leave it loose in the vehicle.

In a sudden stop or accident, it could strike

the occupants or seatbacks and cause

serious personal injury.

WARNING!

(Continued)

WARNING!

Never allow a child to put the shoulder belt

under an arm or behind their back. In a crash,

the shoulder belt will not protect a child

properly, which may result in serious injury or

death. A child must always wear both the lap

and shoulder portions of the seat belt correctly.

21_RUP_OM_EN_USC_t.book Page 303

Содержание Pacifica 2021

















































































































































































































































































































































































































































Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды

Chrysler Pacifica 2021, Руководство пользователя

Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды