Chrysler Pacifica 2021 Скачать руководство пользователя

Страница: 261 / 432

SAFETY

259

ESC Operating Modes

Depending upon model and mode of operation,

the ESC system may have multiple operating

modes.
ESC On
This is the normal operating mode for the ESC.

Whenever the vehicle is started, the ESC system

will be in this mode. This mode should be used

for most driving conditions. Alternate ESC

modes should only be used for specific reasons

as noted in the following paragraphs.
Partial Off
This mode may be useful if the vehicle becomes

stuck. This mode may modify TCS and ESC

thresholds for activation, which allows for more

wheel spin than normally allowed.
To enter the “Partial Off” mode, momentarily

push the ESC OFF button and the ESC OFF

Indicator Light will illuminate. To turn the ESC

on again, momentarily push the ESC OFF button

and the ESC OFF Indicator Light will turn off.

NOTE:

When driving with snow chains, or when starting

off in deep snow, sand, or gravel, it may be

desirable to allow more wheel spin. This can be

accomplished by momentarily pushing the ESC

OFF button to enter partial mode “Partial Off”

mode. Once the situation requiring “Partial Off”

mode is overcome, turn ESC back on by

momentarily pushing the ESC OFF button. This

may be done while the vehicle is in motion.

ESC Activation/Malfunction Indicator Light

And ESC OFF Indicator Light

The ESC Activation/Malfunction

Indicator Light in the instrument

cluster will come on when the ignition

is placed in the ON/RUN mode. It

should go out with the engine running. If the

ESC Activation/Malfunction Indicator Light

comes on continuously with the engine running,

a malfunction has been detected in the ESC

system. If this light remains on after several

ignition cycles, and the vehicle has been driven

several miles (kilometers) at speeds greater

than 30 mph (48 km/h), see an authorized

dealer as soon as possible to have the problem

diagnosed and corrected.
The ESC Activation/Malfunction Indicator Light

starts to flash as soon as the tires lose traction

and the ESC system becomes active. The ESC

Activation/Malfunction Indicator Light also

flashes when TCS is active. If the ESC

Activation/Malfunction Indicator Light begins to

flash during acceleration, ease up on the

accelerator and apply as little throttle as

possible. Be sure to adapt your speed and

driving to the prevailing road conditions.

WARNING!



When in “Partial Off” mode, the TCS func

tionality of ESC (except for the limited slip

feature described in the TCS section) has

been disabled and the “ESC Off Indicator

Light” will be illuminated. When in “Partial

Off” mode, the engine power reduction

feature of TCS is disabled, and the

enhanced vehicle stability offered by the

ESC system is reduced.



Trailer Sway Control (TSC) is disabled when

the ESC system is in the “Partial Off” mode.

21_RUP_OM_EN_USC_t.book Page 259

Содержание Pacifica 2021

















































































































































































































































































































































































































































Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды

Chrysler Pacifica 2021, Руководство пользователя

Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды