Chrysler Pacifica 2021 Скачать руководство пользователя

Страница: 359 / 432

SERVICING AND MAINTENANCE

357

NGINE

Engine Oil Selection

For best performance and maximum protection

under all types of operating conditions, the

manufacturer only recommends engine oils

that are API Certified and meet the

requirements of the manufacturer Material

Standard MS-6395.

American Petroleum Institute (API) Engine

Oil Identification Symbol

This symbol means that the oil has

been certified by the American

Petroleum Institute (API). The

manufacturer only recommends API

Certified engine oils.
This symbol certifies 0W-20, 5W-20, 0W-30,

5W-30 and 10W-30 engine oils.

Synthetic Engine Oils

You may use synthetic engine oils provided the

recommended oil quality requirements are met,

and the recommended maintenance intervals

for oil and filter changes are followed.
Synthetic engine oils which do not have both the

engine oil certification mark and the correct SAE

viscosity grade number should not be used.

Materials Added To Engine Oil

The manufacturer strongly recommends

against the addition of any additives (other than

leak detection dyes) to the engine oil. Engine oil

is an engineered product and its performance

may be impaired by supplemental additives.

Disposing Of Used Engine Oil And Oil

Filters

Care should be taken in disposing of used

engine oil and oil filters from your vehicle. Used

oil and oil filters, indiscriminately discarded, can

present a problem to the environment. Contact

an authorized dealer, service station or

governmental agency for advice on how and

where used oil and oil filters can be safely

discarded in your area.

NGINE

ILTER

The engine oil filter should be replaced with a

new filter at every engine oil change.
Engine Oil Filter Selection
A full-flow type disposable oil filter should be

used for replacement. The quality of replacement

filters varies considerably. Only high quality

Mopar® certified filters should be used.

NGINE

LEANER

ILTER

For the proper maintenance intervals

page 351.

CAUTION!

Do not use chemical flushes in your engine oil

as the chemicals can damage your engine.

Such damage is not covered by the New

Vehicle Limited Warranty.

WARNING!

The air induction system (air cleaner, hoses,

etc.) can provide a measure of protection in the

case of engine backfire. Do not remove the air

induction system (air cleaner, hoses, etc.)

unless such removal is necessary for repair or

maintenance. Make sure that no one is near

the engine compartment before starting the

vehicle with the air induction system (air

cleaner, hoses, etc.) removed. Failure to do so

can result in serious personal injury.

21_RUP_OM_EN_USC_t.book Page 357

Содержание Pacifica 2021

















































































































































































































































































































































































































































Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды

Chrysler Pacifica 2021, Руководство пользователя

Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды