Chrysler Pacifica 2021 Скачать руководство пользователя

Страница: 362 / 432

360

SERVICING AND MAINTENANCE

3. There are glove compartment travel stops

on either side of the glove compartment

door. To release them, push inward on each

travel stop, and pull the glove compartment

door down until the travel stops pass clear

of their hooking points.

4. Open the glove compartment door as far as

possible to gain access to the cabin air filter

compartment cover.

Cabin Air Filter Compartment Cover

5. Pry up the lid of each individual

compartment snap, and detach it from the

rest of the snap. There is a small space on

the side of each snap to use for separating

the lid from the snap. Once detached,

remove the rest of the snap completely from

the compartment cover.

6. After removing the snaps, lift up the

compartment cover to gain access to the

fresh air inlet.

Fresh Air Inlet

7. Remove the filter cover by prying back each

of the retaining tabs from their hooking

points, and then pulling the filter cover out

to expose the cabin air filter. Remove the air

filter by pulling it straight out of the housing.

8. Install the new air filter with the arrow on the

filter pointing toward the floor.

9. Once the filter is replaced, reinstall the filter

cover, making sure the retaining tabs are

fully secured into their housings.

10. Close the cabin air filter compartment

cover, and reinsert the snaps into their

slots. Push the snap lids until fully attached.

11. Push the glove compartment door to the

near closed position to reengage the glove

compartment travel stops. Finally, pull the

glove compartment tension tether clip down

and slide it back into the slot on the side of

the glove compartment door.

1 — Compartment Cover
2 — Compartment Snap

1 — Filter Cover
2 — Retaining Tabs

CAUTION!

The cabin air filter is identified with an arrow

to indicate airflow direction through the filter.

Failure to properly install the filter will result

in the need to replace it more often.

21_RUP_OM_EN_USC_t.book Page 360

Содержание Pacifica 2021

















































































































































































































































































































































































































































Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды

Chrysler Pacifica 2021, Руководство пользователя

Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды