Chrysler Pacifica 2021 Скачать руководство пользователя

Страница: 358 / 432

356

SERVICING AND MAINTENANCE

AINTENANCE

-F

REE

ATTERY

Your vehicle is equipped with a

maintenance-free battery. You will never have

to add water, and periodic maintenance is not

required.

RESSURE

ASHING

Cleaning the engine compartment with a high

pressure washer is not recommended.

VEHICLE MAINTENANCE

An authorized dealer has the qualified service

personnel, special tools, and equipment to

perform all service operations in an expert

manner. Service Manuals are available which

include detailed service information for your

vehicle. Refer to these Service Manuals before

attempting any procedure yourself.

NOTE:

Intentional tampering with emissions control

systems may void your warranty and could result

in civil penalties being assessed against you.

WARNING!



Battery fluid is a corrosive acid solution and

can burn or even blind you. Do not allow

battery fluid to contact your eyes, skin, or

clothing. Do not lean over a battery when

attaching clamps. If acid splashes in eyes

or on skin, flush the area immediately with

large amounts of water

page 339.



Battery gas is flammable and explosive.

Keep flame or sparks away from the

battery. Do not use a booster battery or any

other booster source with an output greater

than 12 Volts. Do not allow cable clamps to

touch each other.



Battery posts, terminals, and related acces

sories contain lead and lead compounds.

Wash hands after handling.

CAUTION!



It is essential when replacing the cables on

the battery that the positive cable is

attached to the positive post and the nega

tive cable is attached to the negative post.

Battery posts are marked positive (+) and

negative (-) and are identified on the battery

case. Cable clamps should be tight on the

terminal posts and free of corrosion.



If a “fast charger” is used while the battery

is in the vehicle, disconnect both vehicle

battery cables before connecting the

charger to the battery. Do not use a “fast

charger” to provide starting voltage.

CAUTION!

Precautions have been taken to safeguard all

parts and connections however, the

pressures generated by these machines is

such that complete protection against water

ingress cannot be guaranteed.

WARNING!

You can be badly injured working on or

around a motor vehicle. Only do service work

for which you have the knowledge and the

proper equipment. If you have any doubt

about your ability to perform a service job,

take your vehicle to a competent mechanic.

21_RUP_OM_EN_USC_t.book Page 356

Содержание Pacifica 2021

















































































































































































































































































































































































































































Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды

Chrysler Pacifica 2021, Руководство пользователя

Результаты поиска

Содержание Pacifica 2021

Отзывы:

Похожие инструкции для Pacifica 2021

Бренды по названию

Популярные бренды