Chopin AlveoPC Скачать руководство пользователя страница 85

Страница: 85 / 174

Chapter 3 Repairs

Maintenance manual
2016/02

AlveoPC

Remove the Alveograph's casing

(see op. A1-1)

Remove the RLP pressure board support

(see op. A1-2)

Disconnect from the CPU board the connector to which the air
pump wires are connected.

Lay the Alveograph on its side, leaning on its block.

Unscrew the four locking nuts on the air pump support under
the Alveo bloc (A), and extract the support from its base with-
out tautening the wires (B). retrieve and keep the washers.

Disconnect the two electrical connections from the solenoid
valve (C). They are marked 16-17 or 18-19 on the connector.

Unscrew the locking nuts on the solenoid valve under the
pump bracket (D).

Cut the cable ties and disconnect the pneumatic hoses using a
flat blade screwdriver and noting their position.

Remove the solenoid valve.

To replace the solenoid valve, perform the above operations in
reverse order with the aid of the diagram to connect the pneumatic
hoses.

Note: We recommend replacing the hoses.

A4: Pneumatic components

Operation A4-5 Removing/replacing a solenoid valve

Page: 1/1

Consumables:

Tools:

L=200

L=300

L=350

L=260

L=450

L=190

L=200

PNEUMATIC DIAGRAM

Expansion
chamber

Pump

Lower plate

Filter

Sensor

Pump sole-
noid valve

Flowmeter

Pressure sensor
solenoid valve

Содержание AlveoPC















































































































































































Результаты поиска

Содержание AlveoPC

Отзывы:

Похожие инструкции для AlveoPC

Бренды по названию

Популярные бренды

Chopin AlveoPC, Руководство по обслуживанию

Результаты поиска

Содержание AlveoPC

Отзывы:

Похожие инструкции для AlveoPC

Бренды по названию

Популярные бренды