Chopin AlveoPC Скачать руководство пользователя страница 125

Страница: 125 / 174

125

Maintenance manual

2016/02

AlveoPC

Extract the mixing blade.

Remove the gear motor, see procedure

B3-1 "Removing/

replacing the gear motor"

, without touching these positioning

spacers.

Remove the retaining ring (A) on the coupling in the reduction
gear.

Then with a wide flat blade screwdriver large, remove the
spring washer (B) just behind the retaining ring.

Take the coupling out of the reduction gear and replace it.

Put the spring washer and the retaining ring back in place on
the coupling shaft (if they are damaged, replace them).

Fit the gear motor, see procedure

B3-1 "Removing/replacing

the gear motor"

Don't forget to check its alignment with the bowl.

Put the mixing blade back in place.

Note: if there is not enough force retaining the mixing blade in the

coupling, adjust the set screw and locknut.

B3: Gear motor

Operation B3-2 Removing/replacing the coupling

Page: 1/1

Consumables:

Tools:

Retaining ring pliers

Locknut

Set screw

Содержание AlveoPC















































































































































































Результаты поиска

Содержание AlveoPC

Отзывы:

Похожие инструкции для AlveoPC

Бренды по названию

Популярные бренды

Chopin AlveoPC, Руководство по обслуживанию

Результаты поиска

Содержание AlveoPC

Отзывы:

Похожие инструкции для AlveoPC

Бренды по названию

Популярные бренды