Chint Power CPS SCE4KTL-O/US Скачать руководство пользователя страница 37

Страница: 37 / 77

IMPORTANT

For further instructions, a RS-485 manual is available with a

detailed configuration that can be used by qualified service

personnel or system installer. Please contact the supplier in order

to obtain this user manual as the reference.

F. DC Protection

This is the over current and over voltage protection that is used for the

Direct Current (DC) side. Please refer to configuration diagram that shown

in Appendix I to connect have a proper configuration for the DC side of PV

system.

The PV Inverter is shipped with dummy fuses (solid aluminum cylinders in

the shape of the proper fuses). Since there are four pairs of DC input

ports, four fuse holders shall be equipped for the four positive (+) polarity

ports and others fuse holders are equipped for the four negative (-)

polarity ports. Therefore, there are supports to have eight fuse folders,

total, to the DC-side as shown in figure 6.2.13.

Figure 6.2.13: Location of DC Fuses Holders

IMPORTANT

The PV Inverter is shipped with a dummy fuse in the fuse holder.

It is necessary to select the proper series fuse depending with the

solar modules that are used. Remove all dummy fuses prior to

installation and operation.

Содержание CPS SCE4KTL-O/US














































































Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды

Chint Power CPS SCE4KTL-O/US, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды