Chint Power CPS SCE4KTL-O/US Скачать руководство пользователя страница 30

Страница: 30 / 77

Page 28 Copyright CPS America Co., Ltd.

C. DC/AC Disconnect

It is the disconnect switch that is used to turn-on and turn-off the power of

the PV Inverter. The switch disconnects both the DC and AC voltage to

and from the PV Inverter.

Electric shock

It is important to avoid touching the DC and AC cabling area

during the procedures even if the AC/DC switch of PV inverter

has been switched off. This is because live powers still remaining

with the cables, please beware.

D. AC Protection

If an external AC breaker or fuse protector is installed, it is not

necessary to implement AC protection fuses within the wiring box. The

specification of external breakers or fuses shall meet the recommended

ratings listed in the following table.

II)

If there is no external AC breaker or fuse protector installed, it is

recommended to have AC protection fuses installed to the AC side. And

the AC fuse that can be selected from the recommended list as below

table indicates.

To ensure the rating of the fuses that are used for the each model is

correct, it is strongly recommended the installer purchase the AC fuses

that have already been tested by CPS.

The recommended list for the AC Fuses:

Table 6.2.1: AC Fuse Specification

Model

Manufacturer

Part Numbers

Fuses Rating

CPS

SCE4KTL-O/US

Littelfuse

KLC 25

25A / 600VAC

CPS

SCE5KTL-O/US

Littelfuse

KLC 30

30A / 600VAC

CPS

SCE6KTL-O/US

Littelfuse

L50S 40

40A / 500VAC

CPS

SCE7KTL-O/US

Littelfuse

L50S 50

50A / 500VAC

Содержание CPS SCE4KTL-O/US














































































Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды

Chint Power CPS SCE4KTL-O/US, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды