Chint Power CPS SCE4KTL-O/US Скачать руководство пользователя страница 70

Страница: 70 / 77

Page 68 Copyright CPS America Co., Ltd.

Output DC Injection too

high

DC Inj high

Output DC current injection is too high

EEPROM Problem

EEPROM

failure

The inside EEPROM has data access problem

Operation Condition

Messages

Descriptions

Communication failure

between microprocessors

SCI failure

Communication between the inside MCU is

abnormal

DC bus voltage is

too high

High DC bus

The DC BUS inside is higher than expected

GFCI detection abnormal

GFCI Failure

The GFCI detection circuit is abnormal

Resistance stick abnormal

Damp Fail

The function of resistance stick is abnormal

11.2 Trouble Shooting Actions

Trouble shooting action for System Faults Messages

A) Isolation Fault

Conditions: The resistance between the PV + or PV – and grounding is

outside the permissible range, <2M

Ω

Corrective Actions:

Restart the inverter again.

If fault still occurs after the unit is restarted, contact the system

installer immediately

Ask the system installer to check if the PV Inverter and PV Modules

are properly insulated throughout the solar system.

B) Grid Fault

Conditions: The grid voltage or grid frequency of the PV Inverter is not

within the permissible range. This can be caused by improper connection

of the AC side; wrong setting of the utility dip switch or the local grid

condition is out of acceptable range.

Corrective Actions:

Check the grid voltage and frequency information from the LCD

displays

If the detected grid voltage is within permissible range, restart the

Содержание CPS SCE4KTL-O/US














































































Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды

Chint Power CPS SCE4KTL-O/US, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды