Chint Power CPS SCE4KTL-O/US Скачать руководство пользователя страница 19

Страница: 19 / 77

5.4 Mount the PV Inverter

Figure 5.4.1: Required Dimension

Select a dry location, out of direct sunlight with ambient temperature

between -20 and 45°C.

IMPORTANT

It is important not to install the CPS grid-tied PV Inverter under

direct sunlight, because the exposure of direct sunlight may

cause an internal heating and also a reduction of output power,

which is known as derating protection.

Select a wall or solid vertical surface which is strong enough to support

the inverter.

WARNING

PV Inverter’s surface and housing can become hot during

operation. Ensure not to install PV Inverters in a location that

contains any flammable

material.

CAUTION

Ensure selected location has a sufficient space for air flow.

Содержание CPS SCE4KTL-O/US














































































Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды

Chint Power CPS SCE4KTL-O/US, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды