Chint Power CPS SCE4KTL-O/US Скачать руководство пользователя

Страница: 47 / 77

Use multi-meter to confirm the total input power of PV strings in order to

ensure the input power from PV strings will not exceed the permissible set

point of 600VDC as the maximum operating voltage of PV inverter and

the maximum DC input current should be within 20A for each pole of DC

terminal.

IMPORTANT

Configuration of the PV modules should be done by qualified

service personnel with the instructions that are provided from the

manufacturer of the PV modules.

Ensure the configuration for each string of the PV-system meets the

specifications required by the CPS grid-tied PV Inverter.

Multi-Meter

It is important to use a multi-meter to measure the DC input voltage

that is generated from the PV modules. It must not exceed 600V

IMPORTANT

The CPS grid-tied PV Inverter is designed with a transformer-less

topology. It is recommended NOT connecting the Inverter with the PV

modules that require positive (+) or negative (-) polarity to ground.

And it is also necessary to have a circuit breaker or fuse switch installed

between PV modules and PV Inverter. When there are PV strings

connected with the circuit breaker or fuse switch, please ensure it is

turned off before connecting the DC cables to the DC input terminals of

PV inverter.

For the DC cables, the terminal connectors are recommended to be

used with cables in order to ensure the effective electric conduction

between DC cables and DC terminals as shown in figure 7.1.2.

Figure 7.1.3: Terminal connectors are required for DC Cables

Содержание CPS SCE4KTL-O/US














































































Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды

Chint Power CPS SCE4KTL-O/US, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды