Chint Power CPS SCE4KTL-O/US Скачать руководство пользователя страница 5

Страница: 5 / 77

Safety Symbols

ELECTRIC SHOCK

Electric shock indicates a potential risk of electric shock if not

avoided.

WARNING

Warning indicates a potentially hazardous situation that could

result in death or serious injury if not avoided.

CAUTION

Caution indicates a hazardous situation that could result in minor

injury if not avoided.

HOT SURFACE

Hot surface indicates a hot surface during operation that could

result in a burn injury if not avoided.

IMPORTANT

Important indicates important and useful information that the user

should know about the system.

ESD Protection

Risk of electric shock can occur when qualified service personnel

are dealing with the electrical components within the PV Inverter,

such as wiring box. An ESD glove should be worn during the

wiring operation, fuse replacement and component installation.

Tool Equipment Symbols

Multi-Meter

Multi-meter symbol indicates that a multi-meter is needed for

measuring to ensure the proper operational functionality of

components.

Tools

Tools symbol indicates that specific tools are required during

installation procedures.

Содержание CPS SCE4KTL-O/US














































































Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды

Chint Power CPS SCE4KTL-O/US, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды