Chint Power CPS SCE4KTL-O/US Скачать руководство пользователя

Страница: 57 / 77

8. LCD Display and Function Structure

8.1 First Level Display Menu

Figure 8.1.1: First level display menu

Operation Status

Output Power

Definition of Level 1 display menu

Operating and Output power Status

Display the operation status and the

instant-output power of the unit.

Etoday and Energy Menu

Display the output energy that is produced on

the current day and the total energy that is

produced since the PV Inverter was installed.

Date and Hour Menu

Display date and time of the current day.

DC Voltage and DC Current Menu

Display the DC voltage and DC current from the

PV array.

AC Voltage and AC Current Menu

Display the output AC voltage and AC current.

Frequency and Output Power

Display the AC frequency and the instant-output

power of the unit.

Nominal Power and Grid System Menu

Display the nominal power of the PV Inverter

and voltage of the AC utility system.

Model Name and Version

Display Model name and the firmware version.

Etoday

Energy

Date

Hour

DC Input Voltage

DC Input Current

AC Output Voltage

AC Output Current

Frequency

Output Power

Model name

Version

Press

Nominal Power

Grid System

Содержание CPS SCE4KTL-O/US














































































Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды

Chint Power CPS SCE4KTL-O/US, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPS SCE4KTL-O/US

Отзывы:

Похожие инструкции для CPS SCE4KTL-O/US

Бренды по названию

Популярные бренды