Chino IR-M21 SERIES Скачать руководство пользователя страница 41

Страница: 41 / 50

INST No INE -403-0P0

−

9.2 Self-diagnosis function

Error message for abnormal operation is displayed by the self-diagnosis function.
The same error message is displayed in the detector unit and the setting display unit.

Erro

No.

Item

Contents

Measures

Self-

diagnosed

abnormality

----- High limit over range Measured value is

higher than display
range.

Check calibration curve
data.
Check output by checker
plate.

----- Low limit over

range

Measured value is lower
than display range.

Check calibration curve
data.
Check output by checker
plate.

Er01 Calibration data error Calibration data is

damaged.

Clear RAM.

Er02 RAM error

Detector unit ram data is
damaged.

Clear RAM.

Er03 Motor rotation

abnormal

Motor stops or rotates
abnormally.

Exchange motor.

Er04 Lamp power supply

abnormal

Lamp power supply is
damaged.

Exchange lamp power
supply unit.

Er05 A/D abnormal

A/D is over range.

Check output by checker
plate.

Er06 Computation error

Computation is
overflow.

Check output by checker
plate.

Er07 Element temperature

abnormal

Element temperature is
abnormal.

Need to return detector
unit to CHINO.

Er10 Calibration curve

data error

Calibration curve data is
not appropriate.

Reset calibration curve
data.

Er11 Knee point line

approximation error

Absorbance x is out of
range of broken line
approximation.

Reset broken line
approximation data.

Er12 Ambient temperature

too high

Ambient temperature of
detector unit is too high

Lower ambient
temperature.

Er13 Ambient temperature

too low

Ambient temperature of
detector unit is too low

Raise temperature.

Er14 Sample temperature

too high

Sample temperature is
higher than correction
range

Widen correction range.

Er15 Sample temperature

too low

Sample temperature is
lower than correction
range

Widen correction range.

Er16 Sample low

reflection

Reflection rate of
sample is low or the
lamp is damaged.

Close distance to sample.
If the lamp is damaged,
exchange it.

Er17 Regression operation

error

Regression operation is
abnormal.

Check calibration curve
sample data.

(Note)

For the items filled with

in the self-diagnosed abnormality, an alarm output for

self-diagnosed abnormality is activated from the setting display unit.

9. Inspection and maintenance

Содержание IR-M21 SERIES



















































Результаты поиска

Содержание IR-M21 SERIES

Отзывы:

Похожие инструкции для IR-M21 SERIES

Бренды по названию

Популярные бренды

Chino IR-M21 SERIES, Инструкция по эксплуатации

Результаты поиска

Содержание IR-M21 SERIES

Отзывы:

Похожие инструкции для IR-M21 SERIES

Бренды по названию

Популярные бренды