Chino IR-M21 SERIES Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 50

background image

INST No. INE-403-0P0

−

12

−

4.3 Multi-detector connections

By using the setting display unit, you can connect the detector unit up to 9 sets.
Two wiring methods are available. One is wiring through a relay box  (IR-WEE ) and the other
is without the relay box (IR-WEE ).

4.3.1 Connections through relay box

4. Connection

C a u t i o n

For both wiring methods, before connecting with the setting display unit or
before turning on the power supply of the setting display unit, number
setting to the detector units is required. For the number setting, be careful
not to overlap any detector unit number of each detector unit.
Refer to [6.2 Setting of detector unit number] for the details.

C a u t i o n

1. Shorten the length of exclusive cable (IR-WERT * mark) as much as

possible.

2. For wiring to the relay box, refer to “Instruction manual of relay box”.

Detector

IR-WERT*

IR- WERT*

IR- WERT*

Relaying box

(Power supply unit is built in)

Relaying box

(Power supply unit is built in)

Relaying box

(Power supply unit is built in)

2-conductor twisted

cable (with shield)

2-conductor twisted

cable (with shield)

2-conductor twisted

cable (with shield)

100-240 V AC

Detector

Detector

Setting diplay unit

«
...
15
16
17
18
19
...
»

Содержание IR-M21 SERIES



















































Отзывы:

Нет отзывов

Похожие инструкции для IR-M21 SERIES

Бренд: Valor Страницы: 13

Бренд: Campbell Страницы: 31

Бренд: Magtrol Страницы: 83

Бренд: Keeler Страницы: 68

Бренд: YOKOGAWA Страницы: 14

Бренд: Kobold Страницы: 44

Бренд: Badger Meter Страницы: 24

Бренд: FM Marin Страницы: 8

Thermo Scientific iCE 3000 Series

Бренд: ThermoFisher Scientific Страницы: 42

Бренд: Camlab Страницы: 28

WTW SensoLyt 900

Бренд: Xylem Страницы: 12

Бренд: Hanna Instruments Страницы: 2

Бренд: Vogel Страницы: 4

K-PATENTS PR-23 AX Series

Бренд: Vaisala Страницы: 246

Бренд: ZIEHL Страницы: 37

Бренд: XPOtool Страницы: 6

Бренд: Simex Страницы: 48

Бренд: netAlly Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды