Chino IR-M21 SERIES Скачать руководство пользователя страница 48

Страница: 48 / 50

INST No INE -403-0P0

−

10.2 Fiber optics

10.2.1 Reflective type fiber

optics

IR-WCRN

Measuring diameter and distance :

20/15mm to

50/50mm

Fiber length :Standard 1.5m

(Maximum 10m)

Minimum bending radius: R100mm
Working temperature range :

0 to 150ºC

Fiber protection : Stainless hose
Purged airflow : 5 to 20Nl/min
Accessory : Horizontal mounting

holder, flange holder

10.2.2 Output checker plate for

reflective type fiber optics
IR-WCRNB

It is used for checking output of the
detector unit on site.
It is used by mounting it on the top of
the fiber optics.

10.2.3 Reflective type fiber

optics with lens IR-WCRE

Measuring diameter and distance:

20/25mm to

40/100mm

Fiber length

: Standard 1.5m

（

Maximum 10m

）

Minimum bending radius: R100mm
Working temperature range:

0 to 150ºC

Fiber protection: Stainless hose
Air purge function: Not provided
Accessory : Horizontal mounting

holder, flange holder

10.2.4 Output checker plate for

reflective type fiber optics
with lens IR-WCREB

It is used for checking output of  the
detector unit on site.
It is used by mounting  it on the top of
fiber optics.

10. Specifications

ºC

The ti p of reflec tion

type fi ber optic s

Purge air inlet 1:Max 60

E side connector

300

Length is as designated. Max1500mm)

D side connector

Purge air inlet 2 (Rc 1/8).

Unit:

(Outer diameterof applicable

6 nylon tube etc.)

Fi tting sc rew for output

check er pl ate

The tip of reflecti on type fiber optics

Output checker plate

G uide pin

47.5

)

Unit:

82.5

300

The ti p of reflec tion type fi ber

optic s w ith l ens attachment

D side connector

E side connector

Unit:

Length is as designated. Max1500mm)

Ou tput chec ker plate

Fitting screw for output

checker plate

The tip of reflection type fiber

optics with lens attachment

Unit:

Guide pin

)

Содержание IR-M21 SERIES



















































Результаты поиска

Содержание IR-M21 SERIES

Отзывы:

Похожие инструкции для IR-M21 SERIES

Бренды по названию

Популярные бренды

Chino IR-M21 SERIES, Инструкция по эксплуатации

Результаты поиска

Содержание IR-M21 SERIES

Отзывы:

Похожие инструкции для IR-M21 SERIES

Бренды по названию

Популярные бренды