Chino IR-M21 SERIES Скачать руководство пользователя страница 14

Страница: 14 / 50

INST No. INE-403-0P0

−

3.3.2 Connection with detector unit

Connect the fiber optics, as shown in the following figure, through the rubber bush attached
to the detector unit.

3.3.3 Disassemble cleaning

For accurate measurements, recommend periodical cleaning of the cover glass in a liquid
contacting part of the measuring cell.

1) Remove the fiber optics (both of light

projecting side and light receiving side),
from the measuring cell.

2) Next, remove 4 screws fixing a connecting

part and remove the connecting part from
the liquid-contacting part.

3) Remove a fitting ring by using the tool A.

Then after screwing the tool B into the
cover glass, pull out the cover glass from
the liquid-contacting part.

4) Wipe off dirt on the glass surface with a

gauze, etc.

5) Confirm that an O ring is inserted in

liquid-contacting part and push in the
cover glass to the liquid-contacting part.

6) Match the positions of E and D characters

of the connecting part and the liquid
contacting part, and fix the connecting
part.

7) After the cleaning of the cover glass, make

sure to re-calibrate your moisture meter.

3. Setting

O UT

I N

Connecting part

4 - Fixing scew

Liquid contacting

part

Tool A

Tool B

Fitting ring

Curler

Cover glass

O ring

Connector for fiber

[Light projecting side ]

Connector for fiber

[Light receiving side]

Dent department

Protrusion department

Rubber bush

Bush fitting ring

Connector ring

Optical fiber

D:Connect to light projecting side

E:Connect to light receiving side

Содержание IR-M21 SERIES



















































Результаты поиска

Содержание IR-M21 SERIES

Отзывы:

Похожие инструкции для IR-M21 SERIES

Бренды по названию

Популярные бренды

Chino IR-M21 SERIES, Инструкция по эксплуатации

Результаты поиска

Содержание IR-M21 SERIES

Отзывы:

Похожие инструкции для IR-M21 SERIES

Бренды по названию

Популярные бренды