- 46 -
[List of Range setting parameters]
Parameter
Function
Default
Set value
INPUT
Select input type
V:
-50.00 to 50.00
V, MV, K, E, J, T, R, S, B, N, U, L, WWRe26,
WRe5-26, NiMo-Ni, Platinel2, PtRh40-20,
Cr-AuFe, Au/Pt, Pt100, QPt100 (old Pt100),
JPt100, Pt50, Pt-Co, UNUSED
RJ
Select whether to use reference junction
compensation contact
*
EXT (external), INT (internal)
BURN
Select whether to detect burnout, and
action at detection
*
None, UP, DOWN
RANGE-L
The lowest end of measuring range used
within the range (measuring range)
determined by the input type
-50.00
-30000 to 30000
Up to three digits after decimal point can be
set. Example: -30.000
The same decimal point position is used for
the lowest/highest range.
RANGE-H
The highest end of measuring range used
within the range (measuring range)
determined by the input type
50.00
SCALE-L
The lowest end of scaling range specified
when selecting the voltage range (mV, etc.)
for input type
-50.00
-30000 to 99999
Up to three digits after decimal point can be
set. Example: -30.000
The same decimal point position is used for
the lowest/highest scaling range.
SCALE-H
The highest end of scaling range specified
when selecting the voltage range (mV, etc.)
for input type
50.00
REC-L
Lowest end of chart recording (left)
-50.00
-30000 to 99999
Up to three digits after decimal point can be
set. Example: -30.000
The same decimal point position is used for
the lowest/highest recording range.
REC-H
Highest end of chart recording (right)
50.00
SHIFT Sensor
correction
Set offset value to the data after scaling
0.00
-30000 to 99999
Up to three digits after decimal point can be
set. Example: -30.000
FILTER
Time constant of input filter (sec).
None
None, 0.5s, 1s, 2s, 3s, 4s, 5s,
UNIT
Set a character string of up to six
characters
V
TAG
Set a character string of up to 10 characters
Not set
Disp
Select ON or OFF for measured value
display
ON ON,
OFF
Rec
Select On or OFF for trace printing
ON
ON, OFF
DIGI.REC
Select On or OFF for digital
recording/printing
ON ON,
OFF
SD-CARD.REC Select On or OFF for SD card recording
ON
ON, OFF
D.Band
Recording deadband
0
0 to 9
3. Copying settings
Pressing the
key on the list of set contents displays the copy window for channel settings.
Move the cursor to the item you want to copy with the
▲
/
▼
/
/
keys.
Press the
key to check
the check box of
desired item.
After selecting items to be copied, specify the source and destination. Move the cursor to the source (Src.CH) and
select CH with the
▲
/
▼
keys (forward/reverse) and then press the
key to register. When the cursor moves to
the destination (Dest.CH), select CH likewise. Settings can be copied to specified channels collectively.
When the destination setting is completed, move the cursor to Copy and press the
key to start copying.
4. Shortcut for input type settings
Only for “input type settings”, a setting window of each channel can be displayed from the measured value display
window. On the each display mode, highlight the channel number you want to set with the
▲
/
▼
/ /
keys and press
the
key. For the case of 1-point display, pressing the
key brings the parameter setting window of the
displayed channel.
* Copy function is unavailable on a setting window displayed using shortcut.
When parameters like input type and scale upper/lower limit are changed in “input type settings”, it may affect other
settings (alarm settings/deadband, etc.).
Please bear this in mind since copying these parameters may also affect other settings.
Influence on other settings
Note
