manualshive.com logo in svg

CBE 520, Безопасность, Установка, Эксплуатация, Обслуживание

Поделиться
Скачать
CBE 520 Скачать руководство пользователя страница 5

 

 

5 

 

WARNINGS AND NOTICES 

 

 

           

WARNING 

 
 
The purpose of this section is to alert operating and maintenance personnel to the possible dangers 
of this type of equipment.  Serious injury and/or equipment damage could result from not heeding 
these safety precautions. 

BEFORE OPERATING EQUIPMENT: 

1.

 

Any personnel working directly with or on this equipment should read this manual before 
proceeding with equipment use. 

 

2.

 

Electricians should familiarize themselves with the electrical drawings before initial start-up 
of equipment. 

 

3.

 

Other appropriate operating and maintenance personnel should familiarize themselves with 
mechanical layout and general arrangement drawings before start-up of equipment. 

 

4.

 

Determine location of all emergency switches. 

 

5.

 

Be sure all guards are in place and observe all warning signs. 

 

6.

 

Be sure electrical equipment is free of any accumulation of water. 

 

7.

 

Be sure all personnel are clear of operating mechanisms before connecting air. 

 

8.

 

Never start equipment without first checking for loose objects, tools and trash.  All persons 
in the immediate area of the equipment should be alerted prior to starting. 

  WHEN OPERATING EQUIPMENT: 

 

1.

 

Do  not  open  junction  boxes  or  control  panels  unless  you  are  a  qualified  electrician.    Be 
sure  power  is  off.    Except  when  electricians  are  performing  maintenance,  electrical 
enclosures and junction boxes should always be securely closed. 

 

2.

 

Stop  machine  and  disconnect  power  before  servicing  or  repairing.    Maintenance  and 
adjustments must be performed with all power disconnected unless otherwise specified in 
this manual. 

3.

 

Do not attempt to defeat any safety switches.  Serious injury could result. 

 

4.

 

While machine control power is on, do not activate limit switches manually.  Serious injury 
and/or machine damage could result.  Disable machine before attempting any maintenance 
or manual testing of components. 

5.

 

Motors  will  get  warm  to  the  touch  and  should  not  cause  concern  for  equipment  reliability  and 
operation.  A temperature rise is normal per new NEMA specifications.

 

Содержание 520






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды