manualshive.com logo in svg

CBE 520, Безопасность, Установка, Эксплуатация, Обслуживание

Поделиться
Скачать
CBE 520 Скачать руководство пользователя страница 17

 

 

17 

 

SETTING CONVEYORS 

 

Once the BB is in place and anchored, use a chalk line to layout any conveyors to the system. 
Refer back to layout drawing to set remaining conveyors. If the BBL is equipped with a powered 
conveyor, this will come secured to the BBL structure. Layout a line parallel line to the powered 
discharge conveyor, maintaining a 1/2" clearance between all conveyors to ensure the conveyor 
units are not touching the scale conveyor.

 

 

 

INSTALLATION SUMMARY 
 

 

Place the 510 series in the selected site. 

 

Align with your discharge spout and connect with flexible collar( supplied by customer) 

 

 

 
 

 

 

NOTE

:  

Assure that each leveling load foot is securely resting on the floor before jamming  

 

 

the load cell nut.  Be sure the Bulk bagger does not rock and is level. Be sure to have 

 

 

 

a minimum of a ¼” maximum of ½” clearance between the frame and the floor.

  

 

 

 

 

CAUTION:  

 

If more than 1/2" clearance to floor is needed, the bottom of the leveling load foot must be shimmed.  

 

Be  sure  the  leveling  load  foot  bolt  thread  engagement  is  a  minimum  of  50%  into  each  of  the  load 
cells. 

 

Tighten  leveling  foot  lock  nut  against  load  cell  being  careful  not  to  over  tighten. 

This  may  cause 

reading errors, which will require re-calibration. 

 

 

 

 

 

NOTE: 

If  removing  the  controller from  the  equipment,  secure  the  controller  to the  desired  location 

 

   

and then the load cell cable to the floor or wall. Re-connect the load cell cable to the weight 

 

   

indicator. Reference the indicator User and Installation Guide for proper  connections. 

Take 

 

   

care not to stretch or bind cable as this will affect weight readings. 

 

 

 
 

 

 

NOTE:  Depending on the model and configuration, your indicator may come pre-connected  

to 

the scale.  

 
 

Содержание 520






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды